mx5 phone holder 3d models

EXCLUSIVE COMPATIBILITY WITH LEFT-HAND DRIVE VEHICLES Among the parts offered here, and for use in a Mazda MX5 ND, you must print two specific pieces: The first piece is the cup-holder insert, which fits into the passenger-side receptacle. ...The second...

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/0PPQnWlK6MU

PHONE HOLDER MAZDA MX5 NC

My redesign incorporates blind mortices for separate clips to allow for fitting adjustment on gluing ensuring it locks into place, a small lens printed in coloured (blue) translucent PETG filament and nipples (steady!) to hold any large mobile phone...

This phone holder of cause works more or less with every phone and car, but it fits into the phone holder base for the cupholder of the MX5 ND from the linked project, which for itself works perfectly. I printed his phone holder and found a few...

Pop out the center console frame of your NBFL Miata and position this phone holder underneath it, then simply snap them back into place.

Summary This Mazda MX5 NA-inspired phone dock was built from scratch, based on a model by DStBone. It's designed for the OnePlus 6T with a case and USB-C charging, but any smaller phone will fit. Changelog v1.1 Added a version with a cup holder...

This is just a basic phone stand featuring the Meizu MX5 model.

MAZDA MX5 PHONE SUPPORT Nb

This support is for Mazda MX5 with rectangular space near clock. I made it for my phone (Oneplus 6 with spigen cover). Housing is 80mm x 12mm. ...No need glue for installation

Created by Thingiverse Customizer Customize this Phone Stand Here: http://www.thingiverse.com/apps/customizer/run?thing_id=41401 Design Specifications: Using the following parameters to customize your phone stand: * Stand Width: Set to 90mm *...

There are two things that I changed with this remix:-The mount now has a rectangular mounting point, for rectangular magnets (I found my phone naturally wanted to rotate), and also has a thicker fixing point.-The files now are converted to Solidworks...

Phone holder/ mount for in a mazda mx5 nb/nbfl that uses the orginal radiocover for the minideck. Needed: 5x M3x20 countersink screws 5x M3 nuts. ... Lever arms must be screwed thight else the phone might drop out during epic cornering.

Remixed Magnet holder part adapted to suit MagSafe sized Mounts. ... Specifically designed to fit the MagSafe mount I already had, Linked below https://www.amazon.co.uk/dp/B08T8RFVC7?ref=ppx_pop_mob_ap_share

Original JDM Solutions Design. ...Over 500 sold. MX5 ashtray Cup holder for MK1 MX5/Eunos

A larger cupholder designed specifically for the Mazda MX5 NA Miata's cupholder support, originally created by 5str3l0k and available here: https://www.thingiverse.com/thing:2501911. The ID hole is 3 inches in diameter, but I'm still working on this...

... from another design. ...To accommodate my iPhone's protective case, I increased its size so that the phone could fit comfortably without needing removal every time. ...The addition of a small Miata face adds a touch of personality to the holder.

... also be a sturdy platform for a funnel to fit. This a bayonet type fitment and has been successfully tested on a Mx5 and a Fiesta 1.0 ecoboost. I understand that NC and ND oil caps are interchangeable So this should fit a ND as well. ...

A Cup Holder Designed Specifically for Fiat/Abarth 124 Spider and MX-5 Miata Owners The original design has been optimized into two separate components to make it easier to print. ...These two pieces must be carefully aligned and glued together to form...

... middle console using the existing screw. To ensure durability, it's recommended to print this design with ABS filament, as it won't melt in direct sunlight. Version 2 of the Cup Holder has been added and significantly improved for a smoother finish.

I made a phone mount that can be stuck to the ND mx-5 infotainment system to record track days. The bracket has a space for M5 nuts on the underside, and I used an M5 thread to camera gear adapter on the upper side. Double sided foam tape on the...

made to replace blanking plate on side of dash that will hold usb cables i made it so one will hold usb cable from headunit and other will hold usb cable for haltech ecu, so you may need to adjust to sut you cables

Uploaded a photo on the Miata 3D Printing Association on facebook (If your not a member its worth checking out!) and had a lot of interest in this so i thought I'd spend some time in thinking about what's needed and designing a couple. This is...

Remixed design of a Storage Bin for the Mazda MX5 ND, that clips into the passenger side cup-holder slot. ...Reworked to fit RHD models, and also to address the spacing of the support on the original design.

enlarged version of cup holder storage with a slot added for phone cable

enlarged version of cup holder storage with a slot added for phone cable Print Settings Printer: BFB IeC refurbished Rafts: No Supports: Yes Resolution: 0.2 Infill: 25% Filament: Filoalfa - Alfapro professional pla black Category: Automotive

Easy-to-access storage that easily fits into the passenger-side cup holder slot. Large, rounded edges ensure passenger comfort. This innovative storage solution comes in two convenient parts, joined by a remarkably simple design featuring a mere...

iPhone 6s holder with lightning connector functionality. The design integrates seamlessly into the original ash tray metal section. Future plans include integrating this system into a charger/DAC audio setup, housed within the lower half of the...

I just needed a bigger cup holder for my Miata, the one by Mirko looked pretty good but it didn't fit my water bottle so I enlarged it a bit. It is now about a 76mm inner diameter. ... The onshape file is attached:...

Phone holder to be printed 2 times one per side several angles available 50°;60°;70°;80 for phone 1.5cm thick modifiable on request do not hesitate to contact me if you see improvements to be made contains solidworks file and stl file phone holder to...