iphone 11 phone holder 3d models

iPhone 11 phone holder for dd1/2,best to have a rubber case on the phone for better fit and protection.

iphone 11 phone holder for DD 1/2, has been designed for a phone with a rubber protective case on for best fit and protection. ... printed with ender 5 with eryone pla filament  infill- 20% quality -0.15 support- everywhere  raft- no

Designed up this dealer button to use in home games or have just as something laying around for any poker fan. It was inspired by a dealer button in Pokerstars VR. Printing: Ring - Infil to add weight, supports needed for spade inset. Letter...

This car mount is designed to hold an iPhone 11 with a case on. The added wedges are needed for some cd slots to give a tighter fit. ...One version is slanted a few degrees toward the driver.

This car mount is designed to hold an iPhone 11 with a case on. The added wedges are needed for some cd slots to give a tighter fit. ...One version is slanted a few degrees toward the driver.

... model takes approximately three hours and forty-one minutes to print. ... Crafted specifically for my iPhone 11, its design places the microphone inlet on the left side of the phone's base and the speaker output on the right side of the phone's base.

Customized version of https://www.thingiverse.com/thing:614516 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=614516

This model is sized specifically for the iPhone 11 regular, so if you see your phone dimensions also match it, feel free to use. The back plate is held by tiny magnets (5 mm diameter x 1.5 mm height), you will need 4 of this, or not, perhaps the lid...

The phone mount was originally designed for my iphone 11 with a slim case on it. The mount can fit a phone that is 3.25" wide by .5" thick or smaller. The mount also features pencil holders for 2 pencils for tournament play or league night. These...

SUP IPHONE 11 PRO MAX

CD slot phone holder for Iphone 11 (fits well with a thick case). Simple design, no need for supports. Charger pin available. Designed for Toyota Corolla CD slot, thickness may vary. Try it. ... PRINT IN PETG OTHERWISE WILL SHRINK AND DEFORM IN A...

An iPhone 11 Pro max in Mous Case or similar width phone (3.25" wide with case) will snap in place to the phone holder. Print 2 Legs and 1 Phone holder plate. Attach with 4x #6 x 1/2" Wood Screws. For use with an ab wheel with foam handle grips...

This is a remix of a very good design but it wouldn't fit my iPhone 11 with an Otterbox case. I made the phone tongs wider and deeper, and changed the screw to have a hex head that is long enough to easily screw in. I printed the bracket and tong...

Customized version of https://www.thingiverse.com/thing:614516 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=614516

This slide-in holder/stand accommodates an iPhone 11 (or other similarly sized device). Designed specifically for a caseless phone, it securely cradles the device without forcing a fit. Space is also provided for a charging cable. ...The mounting...

This is a slide in holder/stand sized to fit an iPhone 11 (or other similarly sized device). Sized for a caseless phone. The phone fits securely but does not require forcing to fit. There is space for a charging cable. ...The mounting bracket is...

I put together this design after picking up an iPhone 11 Pro Max, which didn't fit in my old phone stand. So I created a new one that will hold it securely. Redesigning it took some trial and error - I had to make changes a couple of times before...

Customized version of https://www.thingiverse.com/thing:614516 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=614516

Customized version of https://www.thingiverse.com/thing:614516 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=614516

Customized version of https://www.thingiverse.com/thing:3125740 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3125740

Customized version of https://www.thingiverse.com/thing:3125740 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3125740

this is a iphone 11 phone holder with a port to charge your phone it workes with iphone 11 and 11pro max but not the 11 pro

This iPhone 11 phone case is a rigid fit, not designed with flexibility in mind. ...I created it according to Apple's strict guidelines for official accessories.

iPhone 11 mobile phone holders are essential tools for creating high-quality video content on YouTube and other online platforms. They enable creators to capture professional-looking footage with ease, making them an indispensable part of any...