drill spool winder 3d models
122760 3d models found related to drill spool winder.thingiverse
This a remix of Ajaxjones' mini drill spool winder https://www.thingiverse.com/thing:2085856. ...I shrank down the attachment drum to fit inside the mini filament spool.
thingiverse
Hardware required: - Drill - M8 threaded rod (15-20 cm) - 5x M8 nuts (or 3x M8 nyloc nuts) - 3x M8 large OD nuts Step 1: Screw two nuts to one end of the rod, with the first about 3 cm from the end. This end will be held in the drill chuck. Step 2:...
thingiverse
... m8 or 1/4" bolt as specified in the file name. Files labelled cut are sized for tapping threads for the specified bolt size. 0.25 = 1/4" M8 is M8 There are two sizes. 30 to 61 diameter and 48 to 75 diameter. Both should fit most spools. ...
thingiverse
need to get some 1/2inch rod, I chose aluminum need 1/8 rod to make the cross pin, you need to drill the hole need 2 bearings, 6804 size. ...
thingiverse
Locking Device Prevents Patio Umbrella Spinning When Blocking Sunlight Designed for 37mm umbrella poles, this lock will work on sizes ranging from 36-38, but thorough testing is not available. If you find this useful, consider donating to my PayPal...
thingiverse
I found that the hub provided by the original designer didn't work with some of my spools. So I made a reduced hub for the winder so you can select which is appropriate. Also inspired by the remix by rey_mezcal. My hub goes from 44mm to 22mm. ... ...
thingiverse
I was forced to start over with a new spool because the original one was too wide for my printer's requirements, so I made a custom one that measures 64mm to 44mm. The metal core is a standard 8mm in diameter. I took advantage of Black Friday sales...
cults3d
Added a cone internally so it would print nicely without supports to base plates
thingiverse
Inserted a cone-shaped core within the design to enable smooth printing directly onto base plates without the need for any additional support structures.
thingiverse
This is a remix of Skrycchio's "Filament spool winder with a drill". Being in the US, I don't have metric hardware on hand, so I copied this design but made the hole fit a 1/4" bolt and removed the printed threads because I figured a press fit was...
prusaprinters
A respooling tool for the Bambu spool: https://www.printables.com/model/251457-bambu-lab-reusable-spool-holder-hex-remixInspired on: https://www.printables.com/model/283455-bambulab-spool-winder-for-drill-v2/filesSince I had a lot of spools too wide...
thingiverse
Just another filament spool winder you can use with a drill. This is a remix of my PrintDry Pro spool adapter (which in turn was a remix of a Thingiverse design by Skrutt84: Ender 3 - Filament holder DELUXE). This winder will fit spools with center...
prusaprinters
Use at least 3 perimeters and 5 for the shaft piece. No supports are needed. The hex shaft lets you use a drill.
thingiverse
This is a cap that goes over the hand crank of the Spool Winder by les_kaye that allows you to use a drill with a square bit to turn at higher speeds. Recommend to print the axel with 2mm walls and at least 35% infill. ... ...
thingiverse
So I came up with this simple design to attach to a power drill and wind the spools much quicker. I added a little hot glue to the base of the screw piece to help grip the spool more securely. I highly recommend using two spools for this project. ...
thingiverse
I checked out the options available online but couldn't find a generic one that fit perfectly into my assortment of spools, which I'd partly purchased with a friend. So, I decided to create my own! If your drill has adjustable speed, I highly...
thingiverse
After several minutes of trying to wind a spool of loose filament I finally set a 3 minute timer and told myself I'll just get done whatever I can get done in the next 3 minutes. I might have gotten a few more turns in that time. The filament kept...
thingiverse
easy print spool chuck for hand drill. print the screw at 100% infill or the drill chuck will break the screw there is a flat spot on the collar on the screw print that flat on the bed. use supports print 2 of the spool holders 20% infill no...
prusaprinters
easy print spool chuck for hand drill.print the screw at 100% infill or the drill chuck will break the screwthere is a flat spot on the collar on the screw print that flat on the bed. ...use supportsprint 2 of the spool holders 20% infill no...
thingiverse
This is a spool winder drill bit for the little embroidery thread card spools. ... I printed mine with a layer height of 0.2 mm and a Gyroid fill pattern and 50% fill density.
prusaprinters
This is a remix of the nut designed by @MerlwyndI needed a solution to respool 5kg rolls to 3kg rolls. I simply just extended the threads another 30mm or so. ...This allows you to use wider 3kg rolls to respool.
thingiverse
Used when I splice small spools together I can put them on one spool quickly
thingiverse
I constructed a makeshift attachment to expedite the process of threading fresh wire onto the vacant spool of my trusty Black & Decker GL7033 weed whacker.
thingiverse
i love spool winder from jonmessenger to winding my leftover filament to a new spool, you should check this link : https://www.thingiverse.com/thing:2863263/remixes But, hand crank is too waste my time, so i looked up the drill adapter from funxton...
prusaprinters
I printed spoolholders updated by Joshua Smith https://www.printables.com/model/251457-bambu-lab-reusable-spool-holder-hex-remix but after rewinding one by hand I designed the drill attachment so I could do it faster. changed the model so it...
thingiverse
**Please support my work at: https://www.paypal.me/SalvoOgnibene Also 1$ or 50c are welcomes.** **Don't forget to post your make!** This is a spool winder aid suitable for spools with hole from 52mm to 74mm. Just use a M6 threaded rod and a drill. ...
thingiverse
I absolutely adore this cartridge, so I created a special attachment for my trusty drill to rewind third-party filament effortlessly back onto the daVinci spool. Simply lift open your cartridge and carefully remove the spool. Next, mount it securely...
thingiverse
A little bigger version to account for spools with an inner hole of up to 90mm. I had a spool of abs that had a 72mm inner diameter so I needed it bigger. ...Use M8 or 5/16 hardware.
prusaprinters
<p>You can see it printed and working here: <a...
thingiverse
This item features a compact design with an optional divider and drill winder for wire organization. Holes are included to securely store wound wire, while the winder can be installed to load the wire, then removed when needed. A 1/4 inch bolt (3"...