drill strap winder 3d models

This fits onto your drill to wind up load binder straps. It's specifically designed for the 50mm wide straps. I printed in PLA but I used wall / top & bottom thickness at 2mm. Surprisingly it came out extremely strong. I have used it for 3 days...

This fits snugly onto your drill to tighten load binder straps. Specifically designed for use with 50mm wide straps. I printed mine in PLA, but used a wall thickness and top/bottom layer of 2mm. The result was surprisingly strong. I've been using...

Simply insert the bit into a hand drill and screw it in tight, then feed a few inches of the strap's end through the gap and begin to twist it up. Start with a slow pace and use your other hand to guide the strap as you go, keeping it aligned...

Strap winder for 5 m strap.

This ratchet strap winder is made for 5m strap. Instruction for use: 1) Place the strap into the slot of the rotary part. 2) Align the strap with the slot of the lower part. 3) Push the rotary part into the lower part. You'll hear a click! 4)...

This ratchet strap winder is made for 5m strap.Instruction for use:1) Place the strap into the slot of the rotary part.2) Align the strap with the slot of the lower part.3) Push the rotary part into the lower part. ...You'll hear a click!4) Turn the...

A tool to wind up belts, lashing straps and cables with a power tool like a cordless power drill.To build it needs a M6 hex Bolt, nut and washer (preferably a big washer as seen in my picture).The M6 bolt will fit very snug so it can be tightened...

Hi everyone,Done a simple Belt/Strap Winder as the other day I got annoyed with how long it took to roll up 15 straps! ...Lay it down flat so there is no need for supports.

I despised having knotted ratchet straps, so I made a decision to build a winder myself. I aimed to design the winder in such a way that it wouldn't require supports during printing. ... * 15 Ft Ratchet Strap:...

Place the strap between the Forks then use drill to wind slowly

I hated having tangled ratchet straps, so I decided to make a winder. I wanted to construct the winder so I wouldn't need supports during the print. 15 Ft Ratchet Strap: https://www.amazon.com/gp/product/B01G30J8JY Video of it in use [muting the...

I wanted to construct the winder so I wouldn't need supports during the print. 15 Ft Ratchet Strap: https://www.amazon.com/gp/product/B01G30J8JY Video of it in use [muting the audio is for the best]: https://youtu.be/CXxlw59F7Eg Please feel free to...

The winder works for any straps up to 50mm width. For printing it I used pctg, but many other materials should work too. ...Aditional parts for building: 2x 32x12x10 ball-bearing, 1x m2x20 screw (or a stud), 16mm diameter tube, m5 bolt for the crank, a...

I recommand to use the newer Version 2:https://www.printables.com/de/model/158567-lashing-strap-reeler-winder-v2----------------------------------------------------------------------------------------------------------No more messing up the lashing...

I recommand to use the newer Version 2:https://www.printables.com/de/model/158567-lashing-strap-reeler-winder-v2----------------------------------------------------------------------------------------------------------No more messing up the lashing...

Designed a bit smaller for 4m straps and added an crank.

Zurgurt Aufwickler mit Halteklammer für den gewickelten Gurt benötigt wird noch: Senkkopfschraube M6*30 Sechskantmutter M6 Unterlegscheibe M6 Korosseriescheibe M6 Selbstsichernde Mutter M6 belt winder with retaining clip for the wound belt also need:...

Drill attachment for Stanwood yarn ball winder. ... Snug slip fit over the crank.

This a remix of Ajaxjones' mini drill spool winder https://www.thingiverse.com/thing:2085856. ...I shrank down the attachment drum to fit inside the mini filament spool.

... it quickly. Recommend at least 25% infill and at least 8 walls. Printing slow and at high detail to preserve the thread mesh. You simply chuck up the winder in your drill, place a an empty spool into it, and then thread on the matching cap.

Hardware required: - Drill - M8 threaded rod (15-20 cm) - 5x M8 nuts (or 3x M8 nyloc nuts) - 3x M8 large OD nuts Step 1: Screw two nuts to one end of the rod, with the first about 3 cm from the end. This end will be held in the drill chuck. Step 2:...

This is a cap that goes over the hand crank of the Spool Winder by les_kaye that allows you to use a drill with a square bit to turn at higher speeds. Recommend to print the axel with 2mm walls and at least 35% infill. ... ...

Let's harness the raw power of a drill as a string winder for precision musical instruments! What we have here is an ingenious adapter that connects your drill chuck directly to your tuning pegs, giving you the ability to crank up the speed, snap a...

This is a remix of Skrycchio's "Filament spool winder with a drill". Being in the US, I don't have metric hardware on hand, so I copied this design but made the hole fit a 1/4" bolt and removed the printed threads because I figured a press fit was...

Printing slow and at high detail to preserve the thread mesh. You simply chuck up the winder in your drill, place a an empty spool into it, and then thread on the matching cap. Print Settings Printer Brand: Creality Printer: Ender 5 Rafts: Doesn't...

Just another filament spool winder you can use with a drill. This is a remix of my PrintDry Pro spool adapter (which in turn was a remix of a Thingiverse design by Skrutt84: Ender 3 - Filament holder DELUXE). This winder will fit spools with...

A respooling tool for the Bambu spool: https://www.printables.com/model/251457-bambu-lab-reusable-spool-holder-hex-remixInspired on: https://www.printables.com/model/283455-bambulab-spool-winder-for-drill-v2/filesSince I had a lot of spools too wide...

print the screw at 100% infill or the drill chuck will break the screw there is a flat spot on the collar on the screw print that flat on the bed. use supports print 2 of the spool holders 20% infill no supports print 1 of the nuts 20% infill no...

I was having issues while tufting with the yearn getting stuck and pulling out of my tufting gun. ...I designed a simple spool that can be inserted into a drill to wind the yarn. ... No supports 100% infill

Use at least 3 perimeters and 5 for the shaft piece. No supports are needed. The hex shaft lets you use a drill.