Vikings Lantern - with changeable panels

cults3d

Assemble Candle / tealight covers with 35 changeable panels with Viking's shapes and patterns to choose. 9,5cm diameter 8,7cm high printed in 14 pieces (base, top, 6 bars, 6 panels) no need of glueing (but it's safer to hold it by the bars when moving, especially when tealight or candle is inside) you can additionally lock the bars with a thread (tie it around the cutted part of bars - see photos with an axe) and use the thread as a handle too you can disassemble it, so it will use less storage space, and assemble it again when needed FREE version of Lantern if you want to check if you like the model before you buy the Vikings Set https://cults3d.com/en/3d-model/home/assamble-lantern-with-changeable-panels Assembling and 360* (on the end with normal light and a lighter) video: https://youtu.be/5GyPAtmXjb8 Some outdoor photos and short video with a tealight https://www.instagram.com/p/CUCi8L_r04W/ Test print video with black and white filament with some different panels: https://www.instagram.com/p/CTxdqezFKA_/ Photos of a test print with an additional diffuser: (sorry for print errors) https://www.instagram.com/p/CTzklCDtnEl/ there is 12 basic shapes in 35 configurations all (exept one - Troll Cross - the last on panels list) are in normal (with holes through) and diffused versions (with solid base that diffuse light more) additional diffuser model for a closer to original vikings lanterns look - print it in vase mode (spiralize) for best look you can use a diffuser with or without panels instead of a tealight or a candle you can use a battery light (as on test print photos) - if needed flip the candle cover upside down to have room for a cable Assembling, additional informations: Video shows the easiest way to assemble (bottom and top close to each other when installing bars). Installing bars to base part and then putting on the top part may be little harder Bars will fit only one way (the pointy part to the inside) Panels are better looking when you install them more flat side (usually the first layer, the printer bed side) to the outside If panels will not hold push in top part little harder or use a file to scrap a little plastic on the bars, where top part holds, towards the base (so top part will be closer to base) version 1.1 of bars will hold the top and bottom parts stronger. Normal version is easier to put it Shapes and patterns were used on my Viking's Bookmarks: https://cults3d.com/en/3d-model/home/viking-s-bookmarks-set and Round Vikings Earrings / Talismans: https://cults3d.com/en/3d-model/jewelry/round-vikings-earrings-talismans More Tealight Covers: Zodiac - FREE sample available https://cults3d.com/en/3d-model/home/zodiac-tealight-cover Vikings Lantern - FREE sample available https://cults3d.com/en/3d-model/home/viking-s-candle-covers-set The Little Prince https://cults3d.com/en/3d-model/home/little-prince-tealight-cover Year of the Tiger (Chinese Year 2022) - FREE sample available https://cults3d.com/en/3d-model/home/year-of-the-tiger-tealight-covers-set Christmass and decorative - FREE sample available https://cults3d.com/en/3d-model/home/candle-tealight-covers-set Geometric Shadow Makers - FREE https://cults3d.com/en/3d-model/art/rosette-shadow-maker https://cults3d.com/en/3d-model/home/lattice-shadow-maker Valentine's Day - FREE https://cults3d.com/en/3d-model/home/tealight-covers-for-valentines-day If you will some problems with it just ask. I will try to help :) UPDATE 20 IX 2021 Version 1.1 with beveled holes in base and top parts (will help if your first layer is squished) and with very small ridges on bars and inside base and top (lanter will hold together stronger) New version of Knot_Frame as I notticed that the knot was not seamless UPDATE 18 I 2024 Improved Base, Top and Bars models. It will hold even stronger now Added Test files to check if your slicer and printer settings are right Changed file names to shorter Panels are slightly longer now Fixed some minor model errors Added new photos