UNW P90 MAG MOUNT FOR THE PLANET ECLIPSE ETHA 2, EMEK AND EMF100

cults3d

(the mount is for the 68 cal and 50 cal mags) this mount can be used with or with out the bullpup kit. and makes it possible to use the UNW P90 mags that can hold 28 rounds with your paintball marker. but there are also other options out there. like the G11TIPX mag and Hi-cap mag (hopper adapter). as you can see on the pictures are there a view options when it comes down to the front morning part. this is so you can have custom look. but at the same time also to make this mag mount more flexible for the current mags and future designs. but the original P90 design does help in guiding the mags into place. so in case you don’t like the tall look to the original the low wigged is a good middle ground I do say that the grub screw needs to be at 2mm in hight. that functions to activate the magazines. but it’s possible that is need a slight adjustment. this will be covered in the UNW P90 PDF. I do like the idea of having a smooth top on the grub screw so that is why I like it to be installed the what it’s shown with the hex key mount hole at the bottom of your Mag mount. why the “stippling” with a soldering iron of the insides of the rail mounted parts. well at first I was trying to go for a “good fit” but this was a hard thing to get right. since printing orientations seemed to have a effect on this as well. when tolerances were getting to tight. and making these small lines is easy to do and make it so that you can remove some unwanted play in the parts in case you have some issues with it… the slide. you want the slide to move smoothly and not get stuck when it’s fully compressed. this can be because of support remains or elephant food. but you can also play around with the spring tension if you like I used to use 2 springs with a 0.5mm wide instead of the now recommended 0.6mm wire. since I noticed that adding 1 extra spring with some stiff wire was actually a lot better. so you may want to play around with it so the slide is sliding al the way forward every time when the mag is placed in the mount. compatibility note: this mag mount will work for the Planet Eclipse ETHA 2, EMEK and EMF100 (EMG100) Video Links: UNW P90 Planet eclipse EMF100 editionhttps://www.youtube.com/watch?v=0uPL_J2TmEE&t=3s Video Links to mag options for this mount: UNW P90 Project update: ESG Euro SuperGame 2022 after reporthttps://odysee.com/@UntangleWORKS:a/UNW-P90-2022-update-ESG-after-report:2 UNW P90: step by step mag function check (and a bit of a update)https://www.youtube.com/watch?v=BqOoVJ2hh8shttps://odysee.com/@UntangleWORKS:a/UNW-P90-mag-function-check:b UNW P90 MAG VS those... other paintball MAGShttps://www.youtube.com/watch?v=S-up50s3zvohttps://odysee.com/@UntangleWORKS:a/UNW-P90-MAG-VS-those-other-MAGS:2 UNW P90 mag assembly videohttps://www.youtube.com/watch?v=eI5-sqQGx0Ihttps://odysee.com/@UntangleWORKS:a/UNW-P90-mag-assembly:b UNW P90 mag assembly for the open mag versionhttps://odysee.com/@UntangleWORKS:a/UNW-P90-windows-mag:f The UNW P90 Hi cap mag or in other words a hopper adapter for the UNW P90https://www.youtube.com/watch?v=A3yAlBoDHIghttps://odysee.com/@UntangleWORKS:a/UNW-P90-Hi-cap:b UNW P90 Hi cap mag lidhttps://www.youtube.com/watch?v=L9vtBMNIMkMhttps://odysee.com/@UntangleWORKS:a/UNW-P90-Hi-cap-lid:4 demo about the mag plugs at 12:20https://youtu.be/0uPL_J2TmEE UNW P90: Template ring for the P90 airsoft magshttps://youtu.be/kufvl5E0RiU UNW P90: G11 styled tippmann Tipx mag adapterhttps://www.youtube.com/watch?v=_U-nBrJH1hMhttps://odysee.com/@UntangleWORKS:a/UNW-P90-G11:a UNW P90 mag winderhttps://youtu.be/v1cIc2swRdghttps://odysee.com/@UntangleWORKS:a/UNW-P90-mag-winder:9 UNW P90 mag winder ringhttps://youtu.be/KMoFYRpW4_Ehttps://odysee.com/@UntangleWORKS:a/UNW-P90-mag-winder-ring-B:9 UNW P90 mag speed loaderhttps://youtu.be/lVzFHDjsehghttps://odysee.com/@UntangleWORKS:a/UNW-P90-mag-speed-loader:a UNW P90 mag speed loader bumperhttps://youtu.be/4S5K_jraJXIhttps://odysee.com/@UntangleWORKS:a/UNW-P90-mag-speed-loader-bumper:6 materials needed: 2x spring 6mm OD, 0.6mm wire, 20mm long Note: you can add one more if you like it to give the slide more power 2x M2.5 Bolt 16mm long 1x M5 grub screw Note: this needs to stick 2mm up from the mount, use some callipers for this. 2x M5 bolt 25mm long 1x M5 bolt 35mm long