UNW P90 MAG MOUNT FOR PLANET ECLIPSE paintball markers EGO’s GEO’s ETHA’s ETEK’s

cults3d

(50 cal mount version that works with the PE 50cal set have been added) this mount can be used with your PE markers with out the need of a EMC rail kit. I have tested this on a view models and adjusting by that it looks to work on all there models. this style is a bit more work to install than the feedback version. but it’s more of a low profile design. and in a way do you on;y have to remove 2 clamps and reattach your clamping feedneck to have you marker back for normal subair use. Front mounts variations: as you can see on the pictures are there a view options when it comes down to the front morning part. this is so you can have custom look. but at the same time also to make this mag mount more flexible for the current mags and future designs. but the original P90 design does help in guiding the mags into place. so in case you don’t like the tall look to the original the low wigged is a good middle ground MAG activation screw: I do say that the grub screw needs to be at 2mm in hight. that functions to activate the magazines. but it’s possible that is need a slight adjustment. this will be covered in the UNW P90 PDF. I do like the idea of having a smooth top on the grub screw so that is why I like it to be installed the what it’s shown with the hex key mount hole at the bottom of your Mag mount. The Slide: the slide. you want the slide to move smoothly and not get stuck when it’s fully compressed. this can be because of support remains or elephant food. but you can also play around with the spring tension if you like I used to use 2 springs with a 0.5mm wide instead of the now recommended 0.6mm wire. since I noticed that adding 1 extra spring with some stiff wire was actually a lot better. so you may want to play around with it so the slide is sliding al the way forward every time when the mag is placed in the mount. Shroud note: it got a M-lok mounting option at the bottom. but do keep make sure that the bolts of your M-lok accessory is not to long other wise you might damage you barrel! compatibility note: for my testing did it work for EGO’s and GEO’s the only thing to keep in mind is both those 2 have a slightly different hight so you do need to print 2 separate barrel mounts points in case you have both type of markers and like to switch to one or the other. also the front mounts included in this set are from the UNW P90 ETHA2, EMEK, EMF100 so those are the same in case you have those as well. but I also did include the barrel mounts for the UNW P90 ETHA1 in case you have that model other wise don’t use this ETHA1 barrel mount! so the GEO mounts were tested for: GEO 3 GEO 2 ETHA 1 the EGO mounts were tested for: EGO LV1 EGO 8 EMEK 3 also there are a view barrel options shaft 2 shaft 4 emek 3 barrels with a OD from: 21.40mm, 22.00mm, 22.50mm, 23.00mm, 23.50mm, 24.00mm, 24.50mm Video Links: Video Links to mag options for this mount: UNW P90 Project update: ESG Euro SuperGame 2022 after reporthttps://odysee.com/@UntangleWORKS:a/UNW-P90-2022-update-ESG-after-report:2 UNW P90: step by step mag function check (and a bit of a update)https://www.youtube.com/watch?v=BqOoVJ2hh8shttps://odysee.com/@UntangleWORKS:a/UNW-P90-mag-function-check:b UNW P90 MAG VS those... other paintball MAGShttps://www.youtube.com/watch?v=S-up50s3zvohttps://odysee.com/@UntangleWORKS:a/UNW-P90-MAG-VS-those-other-MAGS:2 UNW P90 mag assembly videohttps://www.youtube.com/watch?v=eI5-sqQGx0Ihttps://odysee.com/@UntangleWORKS:a/UNW-P90-mag-assembly:b UNW P90 mag assembly for the open mag versionhttps://odysee.com/@UntangleWORKS:a/UNW-P90-windows-mag:f The UNW P90 Hi cap mag or in other words a hopper adapter for the UNW P90https://www.youtube.com/watch?v=A3yAlBoDHIghttps://odysee.com/@UntangleWORKS:a/UNW-P90-Hi-cap:b UNW P90 Hi cap mag lidhttps://www.youtube.com/watch?v=L9vtBMNIMkMhttps://odysee.com/@UntangleWORKS:a/UNW-P90-Hi-cap-lid:4 demo about the mag plugs at 12:20https://youtu.be/0uPL_J2TmEE UNW P90: Template ring for the P90 airsoft magshttps://youtu.be/kufvl5E0RiU UNW P90: G11 styled tippmann Tipx mag adapterhttps://www.youtube.com/watch?v=_U-nBrJH1hMhttps://odysee.com/@UntangleWORKS:a/UNW-P90-G11:a UNW P90 mag winderhttps://youtu.be/v1cIc2swRdghttps://odysee.com/@UntangleWORKS:a/UNW-P90-mag-winder:9 UNW P90 mag winder ringhttps://youtu.be/KMoFYRpW4_Ehttps://odysee.com/@UntangleWORKS:a/UNW-P90-mag-winder-ring-B:9 UNW P90 mag speed loaderhttps://youtu.be/lVzFHDjsehghttps://odysee.com/@UntangleWORKS:a/UNW-P90-mag-speed-loader:a UNW P90 mag speed loader bumperhttps://youtu.be/4S5K_jraJXIhttps://odysee.com/@UntangleWORKS:a/UNW-P90-mag-speed-loader-bumper:6 materials needed: MAG mount: 2x spring 6mm OD, 0.6mm wire, 20mm long Note: you can add one more if you like it to give the slide more power 2x M2.5 Bolt 16mm long 1x M5 grub screw Note: this needs to stick 2mm up from the mount, use some calipers for this. 1x M5 bolt 25mm long 2x M5 bolt 35mm long RING style mount: 4x M3 bolt 16mm long Shroud style mount: 10x M3 bolt 16mm long (you could also just mount the shroud with 4 bolts making it 6 in total )