Ultimate Armattan Rooster Collection (R-XSR, TBS Crossfire nano, AKK X2 Ultimate, RDQ Mach 2, GoPro Session, LED strip, Antenna)

prusaprinters

<p>My Armattan setup, designed, printed, tested, redesigned and tested several times :)</p> <p>The R-XSR Mount is a remix of another design, with some modifications to fit the other parts I designed. It is in final, printed with PLA, no support, 20% infill.</p> <p>I use the RDQ Mach 2 as a VTX, it is a very good VTX, has microphone, and good performance, high output power. The RDQ Mach 2 Mount sits on the R-XSR mount, and the VTX clicks inside of it. It is final, printed with PLA, no support, 20% infill.</p> <p>The Antenna Mount sits on the rear end of the quad, it has a hole for the VTX antenna, two RX antennas (90 degree), and it has a place to fit in a LED strip (Aurora RC, 25mm x 6 mm). It is final, printed with PLA, support only from base plate, 20% infill. I printed it on the front side down, so the attaching holes will be strong. Printed supports only from base plate with PrusaControl. The LED holder needs a bit of filing to fit the LED strip perfectly.</p> <p>I designed a Lens Protector for the Rotor Riot Runcam Swift 2, it is work in progress version.</p> <p>Also I designed a Motor Wire Clip to fit on the inner sections of the arms to secure the motor wires. Work in progress version.</p> <p>I will upload photos of finished parts soon. If you have any question, ask me in the comments!</p> <p>UPDATE 2018.08.22. – Added 2306 Hypetrain Motor Softmount</p> <p>Print the softmount from flexible filament, 100% infill.</p> <p>UPDATE 2018.08.22. – Added GoPro Session 5 flexible holder</p> <p>Print the GoPro holder from flexible filament, 100% infill, and diagonal infill, if possible (can be set in Simplify3D).</p> <p>UPDATE 2018.09.26. – Finally added the modified RX mount which supports both the FrSky R-XSR and the Crossfire nano receiver! I will upload photos of it later.</p> <p>UPDATE 2018.09.26. – Added a new component: the AKK X2 Ultimate VTX mount. The VTX can be fitted with or without heatsink. It holds them both very secure, and also ventilates them well. There are several ducts for wiring through it. The VTX needs a 90 degree MMCX antenna pigtail as the stock antenna won't fit well. I will upload photos of it later.</p> <p>I printed it with PLA and ABS, 0,2mm layer height, 20% infill. I placed on the vertical back side of it, minimal supports (use Simplify3D to customize the supports). No need to place supports in the vent holes.</p> <p>UPDATE 2018.09.26. – Added two versions of an antenna holder for the TBS Immortal T antenna for the Crossfire nano receiver, a VTX antenna and a LED strip. I will upload photos of it later.</p> <p>I printed it with PLA and ABS, 0,2mm layer height, 20% infill. I placed on the vertical back side of it, minimal supports (use Simplify3D to customize the supports).</p> <p>Plans for the future: I plan to use, test, break, refine, recreate these designs and hopefully the ultimate Armattan Rooster setup will be created. I am also testing various GoPro Session mounts to finally achieve a jello-free camera mount. I have the Armattan Chameleon Ti, and plan to create these stuff for it too.</p> <p>If you like my designs and use them regularly, consider a small donation :) I promise I will update these models to become better and better.</p> <h3> Print Settings</h3> <p><strong>Printer Brand:</strong></p> <p>Prusa</p> <p><p class="detail-setting printer"><strong>Printer: </strong> <div><p>i3 MK3</p></div><strong>Rafts:</strong></p> <p>No</p> <p><p class="detail-setting supports"><strong>Supports: </strong> <div><p>Yes</p></div><strong>Resolution:</strong></p> <p>0,15</p> <p><p class="detail-setting infill"><strong>Infill: </strong> <div><p>20%</p></div></p> <p><strong>Notes:</strong></p> <p>Constantly updating...</p> </p></p></p> Category: R/C Vehicles