Two-Seat Ornithopter Dune 3D Printing Model | Assembly + Action

gambody

ABOUT THIS 3D MODELThe retro-futuristic world of Dune imagined by Frank Herbert in 1965 proved to be a challenge to bring to the big screens! But through the vivid imagination of Denis Villeneuve, demanding practical effects and excellently executed CGI, this incredible fictional universe gifted us a myriad of refreshing sci-fi visuals that could not leave the 3D printing community indifferent.Meet another majestic vehicle capable of defeating a sandstorm of wilful Arrakis - Two-Seat Ornithopter for 3D printing. The little sibling of the dragonfly-inspired Ornithopter Dune 3D Printing Model operates on four swift articulated wings and allows you to observe the surrounding landscape through the panoramic cockpit glass. Immensely detailed and carefully crafted, it calls for you to become the next Chosen One!ADAPTATION FOR 3D PRINTINGTwo-Seat Ornithopter for 3D printing is an active assembly model and its moderation and adaptation for different types of 3D printers took Gambody team 40 hours in total. For you to receive the cleanest 3D printing result possible and to minimize the amount of filament needed for generated support, the dragonfly vehicle was divided into many assembly parts that are provided as separate STL files. For you to display the model in any desired pose and interact with it, our engineers introduced the special articulation mechanism into the Ornithopter's wings that allows their multidirectional movement. All assembly parts are provided in STL files of FFF/FDM version in recommended positions that were worked out in order to ensure the smoothness of the details’ surfaces after printing and that the 3D printing beginners won’t face difficulties when placing the parts on a build plate. When downloading any model’s file you will also receive “Assembly Manual” for FFF/FDM 1.0 and DLP/SLA 1.0 versions in PDF format. We highly recommend that you get acquainted with the “Assembly video” and “Assembly Manual” before getting down to the Two-Seat Ornithopter model.The model is saved in STL files, a format supported by most 3D printers. All STL files for 3D printing have been checked in Netfabb and no errors were shown.The model’s scale was calculated from the approximate length of the Two-Seat Ornithopter's body which is 14500 mm. The 3D printing model’s chosen scale is 1:64 for the FFF/FDM version and 1:128 for the DLP/SLA version.VERSIONS' SPECIFICATIONSFFF/FDM 1.0 version features:- Contains 49 parts;- A printed model stands 191 mm tall, 477 mm wide, 377 mm deep (platform + folded wings), 159 mm tall, 717 mm wide, 234 mm deep (extended landing gear + unfolded wings);- Elaborately detailed cockpit interior;- Adjustable grip connectors inside wings’ mounts allow multidirectional movement of all wings;- Two variants of landing gear - folded to display the aircraft in flight mode and unfolded to display model without the platform;- The platform is made in the style of the Ornithopter Dune 3D Printing Model's for you to display both models together;- Assembly of the FDM version requires additional “pins” that do not come in STL files but can be made out of short pieces of regular 1.75mm filament;- The cockpit windows come as separate assembly parts to be printed with transparent material, the front window can be 3D printed as one piece or in halves;- You can light up the interior of the Ornithopter;- All parts are divided in such a way that you will print them with the smallest number of support structures.DLP/SLA 1.0 version features:- Contains 35 parts;- A printed model stands 159 mm tall, 717 mm wide, 234 mm deep (platform + folded wings), 80 mm tall, 359 mm wide, 117 mm deep (extended landing gear + unfolded wings);- Elaborately detailed cockpit interior;- Adjustable grip connectors inside wings’ mounts allow multidirectional movement of all wings;- Two variants of landing gear - folded to display the aircraft in flight mode and unfolded to display model without the platform;- The platform is made in the style of the Ornithopter Dune 3D Printing Model's for you to display both models together;- The cockpit windows come to be printed with transparent material;- You can light up the interior of the Ornithopter;- All parts are divided in such a way to fit the build plates and to ensure that support structures are generated where needed.You can get the model of Two-Seat Ornithopter Dune for 3D Printing immediately after the purchase! Just click the green Buy button in the top-right corner of the model’s page. You can pay with PayPal or your credit card.Watch the tutorial on how to assemble Two-Seat Ornithopter Dune 3D Printing Model at Gambody YouTube channel.Also, you may like Ornithopter Dune 3D Printing Model, other Fiction 3D Printing Models or Space Ships 3D Printing Models._______FAQ: Where can I print a model if I have no printer?How to get started with 3D printing?How to set up my 3D printer?How to choose right 3D model print bed positioning? How to paint printed figurine?Below you can find printing recommendations for Cura, Simplify3D, Slic3r and PrusaSlicer software.These are basic settings that were tested in Cura 4.8.0 slicer. The test models were printed on Ultimaker 2, Creality Ender 3, Creality CR-10S Pro V2, Anycubic I3 Mega, Anycubic I3 MegaS 3D printers with PLA and PETG filaments.Disclaimer: The following printing settings are a recommendation, not an obligation. The parameters can vary depending on the peculiarities of your 3D printer, the material you use and especially the particular assembly part at hand. Each part that any model comprises often needs preliminary review and you are free to tweak the settings the way you find suitable.Note:- You can scale up the model (downscaling is not recommended!);- All connectors should be printed at 100% Infill;- For all parts of locks (“ge_lock” in “Source files”) you need to change "Brim" type to "Skirt" in Build Plate Adhesion section.QualityLayer Height: 0.12 mm (you can also set Layer Height at 0.16 or 0.2mm for 0.4mm nozzles)Initial Layer Height: 0.2 mm (carefully level the print bed and keep your Initial Layer Height the same as the main Layer Height)Line Width: 0.4 mmWall Line Width: 0.4 mmOuter Wall Line Width: 0.4 mmInner Wall(s) Line Width: 0.4 mmTop/Bottom Line Width: 0.4 mmInfill Line Width: 0.4 mmSkirt/Brim Line Width: 0.4 mmSupport Line Width: 0.4 mmInitial Layer Line Width: 100%Shell Wall Thickness: 0.8 mmWall Line Count: 2Outer Wall Wipe Distance: 0.3 mmTop Surface Skin Layers: 0Top/Bottom Thickness: 0.6 mmTop Thickness: 0.6 mmTop Layers: 5Bottom Thickness: 0.6 mmBottom Layers: 5Initial Bottom Layers: 5Top/Bottom Pattern: LinesBottom Pattern Initial Layer: LinesTop/Bottom Line Directions: [ ]Outer Wall Inset: 0 mmOptimize Wall Printing Order: CheckCompensate Wall Overlaps: CheckCompensate Inner Wall Overlaps: CheckMinimum Wall Flow: 0%Fill Gaps Between Walls: EverywhereFilter Out Tiny Gaps: CheckHorizontal Expansion: 0 mmInitial Layer Horizontal Expansion: 0 mmHole horizontal expansion: 0Z Seam Alignment: User SpecifiedZ Seam Position: BackZ Seam X: Average length of your printer’s plate (e.g.”150” if your plate is 300mm on the X-axis)Z Seam Y: A value higher than the length of your plate on the Y-axis (e.g. 700)Seam Corner Preference: Hide SeamExtra Skin Wall Count: 1Skin Overlap Percentage: 10%Skin Overlap 0.04 mmInfill Infill Density: 20% (for all smaller parts and for all parts of connectors use 100% Infill)Infill Pattern: TrianglesConnect Infill Lines: CheckInfill Line Directions: [ ]Infill X Offset: 0 mmInfill Y Offset: 0 mmInfill Line Multiplier: 1Extra Infill Wall Count: 0Infill Overlap Percentage: 10-20%Infill Overlap: 0.04 mmSkin Overlap Percentage: 5%Skin Overlap: 0.02 mmInfill Wipe Distance: 0 mmInfill Layer Thickness: 0.24 mmGradual Infill Steps: 0Infill Before Walls: CheckMinimum Infill Area: 0 mm2Skin Removal Width: 0.8 mmTop Skin Removal Width: 0.8 mmBottom Skin Removal Width: 0.8 mmSkin Expand Distance: 0.8Top Skin Expand Distance: 0.8Bottom Skin Expand Distance: 0.8Maximum Skin Angle for Expansion: 90˚Minimum Skin Width for Expansion: 0.0Skin Edge Support Thickness: 0Skin Edge Support Layers: 0Material Initial Layer Flow: 100%Printing Temperature: See your filament settingsInitial Printing Temperature: Your filament settingsFinal Printing Temperature: Your filament settingsBuild Plate Temperature: Your filament settingsBuild Plate Temperature Initial Layer: Your filament settings + 5°Flow: 100% (Important! If you face difficulty printing the model, you may need to adjust the Flow parameter. You may research the topic using the Internet or seek assistance at our Customer Support Team at support@gambody.com)Speed You can increase the printing Speed by 20% when you print simple objects. For small/thin parts you need to decrease the Speed by 25% - 50%.Print Speed: 50 mm/s    Infill Speed: 50 mm/s    Wall Speed: 25 mm/s          Outer Wall Speed:25 mm/s          Inner Wall Speed: 50 mm/sTop/Bottom Speed: 25mm/sSupport Speed: 25 mm/s           Support Infill Speed: 45 mm/s          Support Interface Speed: 25 mm/s                Support Roof Speed: 25 mm/s                Support Floor Speed: 25 mm/sTravel Speed: 80 mm/sInitial Layer Speed: 80 mm/sInitial Layer Print Speed: 20 mm/sInitial Layer Travel Speed: 80 mm/sSkirt/Brim Speed: 20 mm/sZ  Hop Speed: 5 mm/sNumber of Slower Layers: 2Enable Acceleration Control: CheckWhen printing simple objects, you need to set all Acceleration parameters at 500 mm/s. For small/thin parts you need to decrease the Acceleration by 50% - 70%.Travel Enable Retraction: CheckRetraction Distance: 4-8 mm, 1-3 mm for Direct Extruder (This is the most important retraction parameter. You can find your optimal value of Retraction Distance by printing any test object, e.g. bridges, towers etc.)Retraction Speed: 25mm/sRetraction Retract Speed: 25 mm/sRetraction Prime Speed: 25 mm/sRetraction Extra Prime Amount: 0 mm3 Retraction Minimum Travel: 1.5 mmMaximum Retraction Count: 100Minimum Extrusion Distance Window: 6,5 - 10 mmLimit Support Retractions: CheckCombing Mode: AllMax Comb Distance With No Retract: 30 mmRetract Before Outer Wall: CheckAvoid Printed Parts When Travelling: CheckAvoid Supports When Travelling: CheckTravel Avoid Distance: 1 mmLayer Start X: 0.0 mmLayer Start Y: 0.0 mmZ Hop When Retracted: CheckZ Hop Height: 0,3 mmCooling Enable Print Cooling: CheckFan Speed: 100%Regular Fan Speed: 100%Maximum Fan Speed: 100% Regular/Maximum Fan Speed Threshold: 10 sInitial Fan Speed: 0%Regular Fan Speed at Height: 0.36 mmRegular Fan Speed at Layer: 3 Minimum Layer Time: 10 sMinimum Speed: 10 mm/sSupport Generate Support: CheckSupport Structure: Normal (you can try using Tree Support Structure if you have difficulty printing any particular assembly part)Support Placement: Everywhere Support Overhang Angle: 60° (this parameter can range from 30° to 70° depending on the part at hand)Support Pattern: Zig ZagSupport Wall Line Count: 1 (stronger support that might be more difficult to remove) 0 (less strong support but is easier to remove)Support Density: 15%Support Line Distance: 2.6667 mmInitial layer support line distance: 2.667 mmSupport Z Distance: 0.12 mmSupport Top Distance: 0.12 mmSupport Bottom Distance: 0.12 mmSupport X/Y Distance: 0.8-1 mmSupport Distance Priority: Z overrides X/YSupport Stair Step Height: 0.3 mmSupport Stair Step Maximum Width: 5.0 mmSupport Stair Step Minimum Slope Angle: 10°Support Join Distance: 2.0 mmSupport Horizontal Expansion: 0.2 mmSupport Infill Layer Thickness: 0.2 mmGradual Support Infill Steps: 0Minimum Support Area: 2 mmEnable Support Interface: Check (generates additional “pillow” on the support structure that leads to a more even surface, but can be difficult to remove in hard-to-reach areas)Enable Support Roof: CheckEnable Support Floor: CheckSupport Interface Thickness: 0.8 mmSupport Roof Thickness: 0.8 mmSupport Floor Thickness: 0.8 mmSupport Interface Resolution 0.2 mmSupport Interface Density: 50-100%        Support Roof Density: 50-100%Support Roof Line Distance: 0.8 mm        Support Floor Density: 50-100%Support Floor line Distance:  0.4mmSupport Interface Pattern: Grid Support Roof Pattern: Grid (this parameter should differ from Bottom Pattern Initial Layer in “Shell” section)Support Floor Pattern: GridMinimum Support Interface Area: 10mmMinimum Support Roof Area: 10 mmMinimum Support Floor Area: 10 mmSupport Interface Horizontal Expansion: 0.0 mmSupport Roof Horizontal Expansion: 0.0 mmSupport Floor Horizontal Expansion: 0.0 mmFan Speed Override: CheckSupported Skin Fan Speed: 100%Use Towers: CheckTower Diameter: 4 mmMinimum Diameter: 3.0 mmTower Roof Angle: 65° Build Plate Adhesion Build Plate Adhesion Type: Skirt/Brim (For unsteady parts, and those parts that may come unstuck use “Brim”. For bigger assembly parts that have large adhesion area and for all parts of locks and claws that you want to come out clean use "Skirt")Skirt/Brim Minimum Length: 250 mmBrim Width: 8.0 mm       Brim Line Count: 10Brim Only on Outside: CheckMesh Fixes Union Overlapping Volumes: CheckMerged Meshes Overlap: 0.15 mmSpecial ModesPrint Sequence: All at OnceSurface Mode: NormalExperimentalSlicing Tolerance: MiddleMaximum Resolution: 0.01 mmFlow rate compensation max extrusion offset: 0 mmFlow rate compensation factor: 100%This model was tested with PLA material.To avoid printing problems, we recommend the following settings:ExtruderNozzle Diameter: 0.4 mmExtrusion Multiplier: 0.97Extrusion Width: AutoRetraction Distance: 5.00 mmExtra Restart Distance: 0.00 mmRetraction Vertical Lift: 0.08 mmRetraction Speed: 5400.0 mm/minWipe Distance: 5.00 mmLayerPrimary Layer Height: 0.2 mmTop Solid Layers: 8Bottom Solid Layers: 5Outline/Perimeter Shells: 2Outline Direction: Inside-OutFirst Layer Height: 90%First Layer Width: 100%First Layer Speed: 20%AdditionsUse Skirt/Brim: CheckSkirt Layers: 1Skirt Offset from Part: 6.00 mmSkirt Outlines: 5InfillInternal Fill Pattern: Fast HoneycombExternal Fill Patern: RectilinearInterior Fill Percentage: 10%Outline Overlap: 22%Infill Extrusion Width: 100%Minimum Infill Length: 5.00 mmCombine Infill Every: 1 layersExternal Infill Angle Offsets: 45/-45 degSupportGenerate Support Material: CheckSupport Infill Percentage: 15%Extra Inflation Distance: 1.00 mmSupport Base Layers: 0Combine Support Every: 1 layersDense Support Layers: 0Dense Infill Percentage: 70%Support Type: NormalSupport Pillar Resolution: 5.00 mmMax Overhang Angle: 60 degHorizontal Offset From Part: 0.50 mmUpper Vertical Separation Layers: 1Lower Vertical Separation Layers: 1Support Infill Angles: 45 degTemperatureExtruder 1 Temperature: 210Heated Bed: 60CoolingIncrease fan speed for layers below: 45.0 sec  Maximum Cooling fan speed: 50%Bridging fan speed override: 100%SpeedsDefault Printing Speed: 4800.0 mm/minOutline Underspeed: 50%Solid Infill Underspeed: 80%Support Structure Underspeed: 80%X/Y Axis Movement Speed: 10800.0 mm/minZ Axis Movemen Speed: 1002.0 mm/minAdjust printing speed for layers below: 15.0 sec   Allow speed reduction down to: 20%OtherUnsupported area threshold: 20.0 sq mThese basic 3D printing settings recommendations for beginners were tested in Slic3r 1.3.0 software. Test models were printed on Ultimaker 2, Creality Ender 3, Creality Cr-10S pro v2, Anycubic I3 Mega, Anycubic I3 MegaS, Anycubic Vyper with PLA and PetG filaments. Note:- You can upscale your 3D printing models. Downscaling is not recommended - it can make smaller parts of the model unprintable, distort the model’s level of detail and result in assembly issues. - All connectors should be printed at 100% Infill.- When printing Lock connectors, we recommend setting the “Brim width” parameter to 0 in the "Skirt and Brim" print settings. In that way, the Locks will be 3D printed with a Skirt only.