Tusken Raider Bust 3D Printing Miniature | Static

gambody

HISTORY OF THE TUSKEN RAIDERThe people of the Sands or the Tusken Raiders are primitive nomad tribes of Tatooine hostile to the local settlers. The people of the sand called them because of living in the desert. However, in the late days after the attacks on Fort Tusken, the race was called the Tusken Raiders. Despite the fact that this term was most often used to refer to all members of the race, in fact, it only concerned members of attacks on settlements. Scientists studying the past of the Tusken have used the name of the Hump to refer to their early settled culture and also the term Kumuga designating the very first intelligent civilization on the planet. In the Tusken culture, the exposure of any part of the body under prohibition is considered as a disgrace.ABOUT THIS 3D MINIATUREThe model is saved in STL files, a format supported by most 3D printers. This model contains only 2 parts and executed in the form of the solid figure therefore, it is available for all types of printers FFF/FDM, SLS/SLA. You can reduce its size and will not lose its quality of print. SLS/SLA version made x2 smaller for economy your material.All STL files for 3D printing have been checked in Netfabb and no errors were shown.Note: Before starting 3D printing the model, read the Printing Details for CURA 3.2.1. software.Scale: His tall in life is 1900 mm. Model made as 1/4 scale in FDM version and 1/8 in SLS/SLA version.FDM version dimension:- After being printed will stand: 172 mm tall, 172 mm wide, 138 mm deep;SLS/SLA version dimension:- After being printed will stand: 86 mm tall, 86 mm wide, 69 mm deep;WHAT WILL YOU GET AFTER PURCHASE?- STL files of Tusken Raider Bust​ for printing which consist of 2 parts.- Two versions of this model;- Available for all types of printers FFF/FDM and SLS/SLA.- Detailed settings that we provide for Cura 3.2.1 for the best print.- High-poly detailed miniature of Tusken Raider Bust​ in two versions.- Full technical support from the Gambody Support Team.Watch the video presentation about Tusken Raider Bust for 3D Printing at Gambody YouTube channel. You can get Tusken Raider 3D Printing Bust right now! Just click the green Buy button in the top-right corner of the model’s page. You can pay with PayPal or your credit card.Also, you may like other Busts 3D Miniatures as well as 3D Miniatures of Star Wars._______FAQ: Where can I print a model if I have no printer?How to get started with 3D printing?How to set up my 3D printer?How to choose right 3D model print bed positioning? How to paint printed figurineThis model was tested in Cura 3.2.1 and printed on an Ultimaker 2 in PLA material.To avoid printing problems, we recommend the following settings:QualityLayer Height: 0.1 mmInitial Layer Height: 0.3 mmLine Width: 0.4 mm Wall Line Width: 0.4 mm   Outer Wall Line Width: 0.4 mm   Inner Wall(s) Line Width: 0.4 mm Top/Bottom Line Width: 0.4 mm Infill Line Width: 0.4 mm Skirt/Brim Line Width: 0.4 mm Initial Layer Line Width: 100%Shell Wall Thickness: 0.8 mm    Wall Line Count: 2Outer Wall Wipe Distance: 0.2 mmTop Surface Skin Layers: 0Top/Bottom Thickness: 0.8 mm   Top Thickness: 0.8 mm       Top Layers: 8    Bottom Thickness: 0.8 mm      Bottom Layers: 8Top/Bottom Pattern: LinesBottom Pattern Initial Layer: LinesTop/Bottom Line Directions: [ ]Outer Wall Inset: 0 mmCompensate Wall Overlaps: Check    Compensate Outer Wall Overlaps: Check    Compensate Inner Wall Overlaps: CheckFill Gaps Between Walls: EverywhereFilter Out Tiny Gaps: CheckHorizontal Expansion: 0 mmInitial Layer Horizontal Expansion: 0 mmZ Seam Alignment: Sharpest CornerSeam Corner Preference: Hide SeamIgnore Small Z Gaps: CheckExtra Skin Wall Count: 1Infill Infill Density: 20%Infill Line Distance: 4.0 mmInfill Pattern: GridInfill Line Directions: [ ]Infill X Offset: 0 mmInfill Y Offset: 0 mmInfill Overlap Percentage: 10%    Infill Overlap: 0.04 mmSkin Overlap Percentage: 5%    Skin Overlap: 0.02 mmInfill Wipe Distance: 0.1 mmInfill Layer Thickness: 0.1 mmGradual Infill Steps: 0Infill Before Walls: CheckMinimum Infill Area: 0 mm2Skin Removal Width: 0.8 mm    Top Skin Removal Width: 0.8 mm    Bottom Skin Removal Width: 0.8 mmSkin Expand Distance: 0.8    Top Skin Expand Distance: 0.8    Bottom Skin Expand Distance: 0.8Maximum Skin Angle for Expansion: 90˚    Minimum Skin Width for Expansion: 0.0Material Enable Retraction: CheckRetraction Extra Prime Amount: 0 mm3 Retraction Minimum Travel: 0.8 mmMaximum Retraction Count: 90Minimum Extrusion Distance Window: 6.5 mmNozzle Switch Retraction Distance: 16 mmNozzle Switch Retraction Speed: 20 mm/s    Nozzle Switch Retract Speed: 20 mm/s    Nozzle Switch Prime Speed: 20 mm/s Speed Print Speed: 45 mm/s    Infill Speed: 50 mm/s    Wall Speed: 22.5 mm/s      Outer Wall Speed: 22.5 mm/s      Inner Wall Speed: 45 mm/s    Top/Bottom Speed: 15 mm/sTravel Speed: 120 mm/sInitial Layer Speed: 30 mm/s  Initial Layer Print Speed: 30 mm/s  Initial Layer Travel Speed: 60 mm/sSkirt/Brim Speed: 30 mm/sMaximum Z Speed: 0 mm/sNumber of Slower Layers: 2Travel Combing Mode: AllAvoid Printed Parts when Traveling: CheckTravel Avoid Distance: 0.625 mmLayer Start X: 0.0 mmLayer Start Y: 0.0 mmCooling Enable Print Cooling: CheckFan Speed: 100%    Regular Fan Speed: 100%    Maximum Fan Speed: 100% Regular/Maximum Fan Speed Threshold: 10 sInitial Fan Speed: 0%Regular Fan Speed at Height: 0.3 mm    Regular Fan Speed at Layer: 2 Minimum Layer Time: 5 sMinimum Speed: 10 mm/sSupport Generate Support: CheckSupport Placement: EverywhereSupport Overhang Angle: 60°Support Pattern: Zig ZagConnect Support ZigZags: CheckSupport Density: 15 %    Support Line Distance: 1.3333 mmSupport Z Distance: 0.3 mm    Support Top Distance: 0.3 mm    Support Bottom Distance: 0.3 mmSupport X/Y Distance: 0.7 mmSupport Distance Priority: Z overrides X/YMinimum Support X/Y Distance: 0.2 mmSupport Stair Step Height: 0.3 mmSupport Stair Step Maximum Width: 5.0 mmSupport Join Distance: 2.0 mmSupport Horizontal Expansion: 0.2 mmSupport Infill Layer Thickness: 0.1 mmUse Towers: CheckTower Diameter: 3.0 mmMinimum Diameter: 3.0 mmTower Roof Angle: 65° Build Plate Adhesion Build Plate Adhesion Type: BrimSkirt/Brim Minimum Length: 250 mmBrim Width: 8.0 mm    Brim Line Count: 18 Brim Only on Outside: CheckMesh Fixes Union Overlapping Volumes: CheckMerged Meshes Overlap: 0.15 mmSpecial ModesPrint Sequence: All at OnceSurface Mode: NormalExperimentalSlicing Tolerance: MiddleMaximum Resolution: 0.01 mmFlow rate compensation max extrusion offset: 0 mmFlow rate compensation factor: 100%Disclaimer: This model will look outstanding if printed on SLA/SLS 3D printer. The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.