Tool Organizer with Cutout for Prusa i3 MK2 MK2S LCD

prusaprinters

<p>WARNING: This is at LEAST a 48 hour print,will require a large build surface</p> <p>(roughly 200mmx200mmx200mm) and will use up about 500g of filament.</p> <p>This is a tool organizer for the items I use with my printer. This is a bit specific to my tools but maybe someone else can use it too. It features slots for the following tools specifically:</p> <p>E3D Nozzle Cross Wrench: <a href="https://www.filastruder.com/products/e3d-nozzle-spanner-wrench">https://www.filastruder.com/products/e3d-nozzle-spanner-wrench</a></p> <p>Foreasy 3D Printer Tools: https://www.amazon.com/gp/product/B01A81FXMK/ref=oh_aui_detailpage_o00_s00?ie=UTF8&amp;psc=1</p> <p>BuildTak BT30185 Spatula: https://www.amazon.com/gp/product/B017XGEDOM/ref=oh_aui_detailpage_o00_s00?ie=UTF8&amp;psc=1</p> <p>Gizmo Dorks 3D Print Removal Tool: https://www.amazon.com/gp/product/B01DTLWVSU/ref=oh_aui_detailpage_o03_s00?ie=UTF8&amp;psc=1</p> <p>Super Lube 21030 Synthetic Grease: https://www.amazon.com/Super-Lube-21030-Synthetic-Grease/dp/B072QW3LG7/ref=sr_1_6?s=industrial&amp;ie=UTF8&amp;qid=1502332625&amp;sr=1-6&amp;keywords=super+lube</p> <p>Brass Brush: https://www.amazon.com/gp/product/B019HPVULQ/ref=oh_aui_detailpage_o01_s00?ie=UTF8&amp;psc=1</p> <p>It also has three pockets for generic stuff like pliers, flush cutters, tweezers, wrenches, etc.</p> <p>The LCD shown is the LCD that comes off the Prusa, All I did was unclip the zip ties leaving the brackets attached so it sits on a table. The tool organizer prints with a cavity for it to sit over the LCD casing. I opted to superglue it in the cavity being mindful of where the SD card slot is to make it one solid unit.</p> <h3>Print Settings</h3> <p><strong>Printer Brand:</strong></p> <p>Prusa</p> <p class="detail-setting printer"><strong>Printer: </strong> <div><p>Prusa Mk2</p></div> <p><strong>Rafts:</strong></p> <p>No</p> <p class="detail-setting supports"><strong>Supports: </strong> <div><p>Yes</p></div> <p><strong>Resolution:</strong></p> <p>.20</p> <p class="detail-setting infill"><strong>Infill: </strong> <div><p>5%</p></div> <p><strong>Notes:</strong></p> <p>Supports are a MUST to make the cavity for the LCD. Play around to make a support pattern that you think is best. I did mine diagonally so that the bridge is well supported. Infill is super low to save plastic. I used honeycomb. Be aware that you may need many top layers due to the low infill. I have some minor errors in the bottom of the pockets where the edges have holes. I think its due to the low infill but not enough top layers to properly seal it. Still perfectly functional for what its for.</p> </p></p></p> Category: 3D Printer Accessories