Titanosaurus 3D Printing Figurine | Assembly

gambody

HISTORY OF TITANOSAURUSTitanosaurus shares his name with a real dinosaur genus but they do not share many similarities other than that. Titanosaurus is a deep-sea dwelling creature who sports a fin on his tail and along his back. This creature first appeared in the 1975 Godzilla film, Terror of Mechagodzilla, where he was used to try and destroy Godzilla, but the attempt failed. Titanosaurus, technically, is not evil since he was mind-controlled in Terror of Mechagodzilla. Some of the characters in the film also mention that Titanosaurus has a calm nature and would normally not attack. Godzilla defeated Titanosaurus by shooting him with two shots of atomic breath. After the second shot of Godzilla’s beams, Titanosaurus fell down an ocean-side cliff never to be seen again.ABOUT THIS 3D FIGURINEThe model is saved in STL files, a format supported by most 3D printers. FDM version features:- Contain 19 parts;- Made with Locks for better fixing. One part of Lock (5_Ge_lock_10H_(X12)) you need to print 12 times. One part of Lock (12_Ge_lock_7S_(X1)) you need to print 1 time- Made with 2 variants of the platform. Divided and Solid for different sizes of buildplates;- All parts are divided in such way that you will print them with the smallest amount of supports.DLP/SLA version features:- Same as FDM but smaller, also made as 9 parts;SLS version features:- Same as SLA but made as 1 part for economy your material;All STL files for 3D printing have been checked in Netfabb and no errors were shown.Note: Before starting 3D printing the model, read the Printing Details for CURA 3.4.1. or Simplify3D Software.There are 19 parts for FFF/FDM version, 9 parts for DLP/SLA version and 1 part for SLS.Scale: Titanosaurus height is 60000 mm. The scale of this model made in proportion to it. 1/250 for FDM version and 1/500 for SLA/SLS version.FFF/FDM version dimensions:After being printed will stand - 244 mm tall, 120 mm wide, 217 mm deep;DLP/SLA/​SLS version dimensions:After being printed will stand - 122 mm tall, 108 mm wide, 60 mm deep;- Has a few details, to keep printing costs down.WHAT WILL YOU GET AFTER PURCHASE?- STL files of Titanosaurus 3D Figurine for 3D printing which consist of 29 parts;- 3 versions of files for this model for FFF/FDM, DLP/SLA, and SLS;- High-poly detailed figurine of Titanosaurus;- Detailed settings that we provide for Cura 3.4.1. and Simplify3D for the best print;- Full technical support from the Gambody Support Team.You can get Model of Titanosaurus for 3D Printing right now! Just click the green Buy button in the top-right corner of the model’s page. You can pay with PayPal or your credit card.Watch the tutorial video on how to assemble Titanosaurus 3D Printing Figurine at Gambody YouTube channel.Also, you may like other Kaiju 3D Printing Figurines._______FAQ: Where can I print a model if I have no printer?How to get started with 3D printing?How to set up my 3D printer?How to choose right 3D model print bed positioning? How to paint printed figurine?This model was tested in Cura 3.4.1 and printed on an Ultimaker 2 in PLA material. Below you can find printing recommendations for Cura and Simplify3D softwares.Recommendations: For all parts of Locks you need to change "Brim" type to "Skirt" in Build Plate Adhesion section.To avoid printing problems, we recommend the following settings:QualityLayer Height: 0.1 mmInitial Layer Height: 0.3 mmLine Width: 0.4 mm Wall Line Width: 0.4 mm   Outer Wall Line Width: 0.4 mm   Inner Wall(s) Line Width: 0.4 mm Top/Bottom Line Width: 0.4 mm Infill Line Width: 0.4 mm Skirt/Brim Line Width: 0.4 mmSupport Line Width: 0.4 mm Initial Layer Line Width: 100%Shell Wall Thickness: 0.8 mm    Wall Line Count: 2Outer Wall Wipe Distance: 0.2 mmTop Surface Skin Layers: 0Top/Bottom Thickness: 0.8 mm   Top Thickness: 0.8 mm       Top Layers: 8    Bottom Thickness: 0.8 mm      Bottom Layers: 8Top/Bottom Pattern: LinesBottom Pattern Initial Layer: LinesTop/Bottom Line Directions: [ ]Outer Wall Inset: 0 mmCompensate Wall Overlaps: Check    Compensate Outer Wall Overlaps: Check    Compensate Inner Wall Overlaps: CheckFill Gaps Between Walls: EverywhereFilter Out Tiny Gaps: CheckHorizontal Expansion: 0 mmInitial Layer Horizontal Expansion: 0 mmZ Seam Alignment: Sharpest CornerSeam Corner Preference: Hide SeamIgnore Small Z Gaps: CheckExtra Skin Wall Count: 1Infill Infill Density: 20%Infill Line Distance: 4.0 mmInfill Pattern: GridInfill Line Directions: [ ]Infill X Offset: 0 mmInfill Y Offset: 0 mmInfill Overlap Percentage: 10%    Infill Overlap: 0.04 mmSkin Overlap Percentage: 5%    Skin Overlap: 0.02 mmInfill Wipe Distance: 0.1 mmInfill Layer Thickness: 0.1 mmGradual Infill Steps: 1Gradual Infill Steps Height: 1.5 mmInfill Before Walls: CheckMinimum Infill Area: 0 mm2Skin Removal Width: 0.8 mm    Top Skin Removal Width: 0.8 mm    Bottom Skin Removal Width: 0.8 mmSkin Expand Distance: 0.8    Top Skin Expand Distance: 0.8    Bottom Skin Expand Distance: 0.8Maximum Skin Angle for Expansion: 90˚    Minimum Skin Width for Expansion: 0.0Material Initial Layer Flow: 100%Enable Retraction: CheckRetraction Extra Prime Amount: 0 mm3 Retraction Minimum Travel: 0.8 mmMaximum Retraction Count: 90Minimum Extrusion Distance Window: 6.5 mmNozzle Switch Retraction Distance: 16 mmNozzle Switch Retraction Speed: 20 mm/s    Nozzle Switch Retract Speed: 20 mm/s    Nozzle Switch Prime Speed: 20 mm/s Speed Print Speed: 45 mm/s    Infill Speed: 50 mm/s    Wall Speed: 22.5 mm/s      Outer Wall Speed: 22.5 mm/s      Inner Wall Speed: 45 mm/s    Top/Bottom Speed: 15 mm/s    Support Speed: 45 mm/s      Support Infill Speed: 45 mm/sTravel Speed: 60 mm/sInitial Layer Speed: 22.5 mm/s  Initial Layer Print Speed: 22.5 mm/s  Initial Layer Travel Speed: 30 mm/sSkirt/Brim Speed: 30 mm/sMaximum Z Speed: 0 mm/sNumber of Slower Layers: 2Travel Combing Mode: AllAvoid Printed Parts when Traveling: CheckTravel Avoid Distance: 0.6562 mmLayer Start X: 0.0 mmLayer Start Y: 0.0 mmCooling Enable Print Cooling: CheckFan Speed: 100%    Regular Fan Speed: 100%    Maximum Fan Speed: 100% Regular/Maximum Fan Speed Threshold: 10 sInitial Fan Speed: 0%Regular Fan Speed at Height: 0.3 mm    Regular Fan Speed at Layer: 2 Minimum Layer Time: 5 sMinimum Speed: 10 mm/sSupport Generate Support: CheckSupport Placement: EverywhereSupport Overhang Angle: 50°Support Pattern: Zig ZagConnect Support ZigZags: CheckSupport Density: 15 %    Support Line Distance: 1.3333 mmSupport Z Distance: 0.3 mm    Support Top Distance: 0.3 mm    Support Bottom Distance: 0.3 mmSupport X/Y Distance: 1 mmSupport Distance Priority: Z overrides X/YMinimum Support X/Y Distance: 0.25 mmSupport Stair Step Height: 0.3 mmSupport Stair Step Maximum Width: 5.0 mmSupport Join Distance: 2.0 mmSupport Horizontal Expansion: 0.2 mmSupport Infill Layer Thickness: 0.1 mmGradual Support Infill Steps: 0Use Towers: CheckTower Diameter: 3.0 mmMinimum Diameter: 3.0 mmTower Roof Angle: 65° Build Plate Adhesion Build Plate Adhesion Type: Brim (for all parts of locks use "Skirt")Skirt/Brim Minimum Length: 250 mmBrim Width: 8.0 mm    Brim Line Count: 18 Brim Only on Outside: CheckMesh Fixes Union Overlapping Volumes: CheckMerged Meshes Overlap: 0.15 mmSpecial ModesPrint Sequence: All at OnceSurface Mode: NormalExperimentalSlicing Tolerance: MiddleMaximum Resolution: 0.01 mmFlow rate compensation max extrusion offset: 0 mmFlow rate compensation factor: 100%Disclaimer: This model will look outstanding if printed on SLA/SLS 3D printer. The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.This model was tested with PLA material.To avoid printing problems, we recommend the following settings:ExtruderNozzle Diameter: 0.4 mmExtrusion Multiplier: 0.97Extrusion Width: AutoRetraction Distance: 5.00 mmExtra Restart Distance: 0.00 mmRetraction Vertical Lift: 0.08 mmRetraction Speed: 5400.0 mm/minWipe Distance: 5.00 mmLayerPrimary Layer Height: 0.2 mmTop Solid Layers: 8Bottom Solid Layers: 5Outline/Perimeter Shells: 2Outline Direction: Inside-OutFirst Layer Height: 90%First Layer Width: 100%First Layer Speed: 20%AdditionsUse Skirt/Brim: CheckSkirt Layers: 1Skirt Offset from Part: 6.00 mmSkirt Outlines: 5InfillInternal Fill Pattern: Fast HoneycombExternal Fill Patern: RectilinearInterior Fill Percentage: 10%Outline Overlap: 22%Infill Extrusion Width: 100%Minimum Infill Length: 5.00 mmCombine Infill Every: 1 layersExternal Infill Angle Offsets: 45/-45 degSupportGenerate Support Material: CheckSupport Infill Percentage: 15%Extra Inflation Distance: 1.00 mmSupport Base Layers: 0Combine Support Every: 1 layersDense Support Layers: 0Dense Infill Percentage: 70%Support Type: NormalSupport Pillar Resolution: 5.00 mmMax Overhang Angle: 60 degHorizontal Offset From Part: 0.50 mmUpper Vertical Separation Layers: 1Lower Vertical Separation Layers: 1Support Infill Angles: 45 degTemperatureExtruder 1 Temperature: 210Heated Bed: 60CoolingIncrease fan speed for layers below: 45.0 sec  Maximum Cooling fan speed: 50%Bridging fan speed override: 100%SpeedsDefault Printing Speed: 4800.0 mm/minOutline Underspeed: 50%Solid Infill Underspeed: 80%Support Structure Underspeed: 80%X/Y Axis Movement Speed: 10800.0 mm/minZ Axis Movemen Speed: 1002.0 mm/minAdjust printing speed for layers below: 15.0 sec   Allow speed reduction down to: 20%OtherUnsupported area threshold: 20.0 sq m