Terran Marine 3D Model in Idle Position | Static Figure

gambody

This model shows the Terran Marine action figure in idle position. Holding his C-14 Gaus Rifle close to his powered armor suit, the Marine is in standby mode, awaiting instructions. This accurately designed 3D model complements the Terran Marine with the rifle pointed up. Print them and gather your own infantry of Terran Marines.  Terran Marine 3D figure in idle position is 139mm deep, 140.81mm wide, and 160mm tall. It will take you no longer than 65h and no more than 309g or 39m of filament to have it 3D printedAs in the case of all our 3D models, Terran files are available for download in STL format and perfectly print out on an average priced SLA/SLS or FFF printer.The provided 3D printable files have undergone correction and adjustment in Netfabb. They have been created in CURA 15.06 and Repetier Host and are free of any error.Buy Terran Marine 3D printer files by clicking on the “Buy” button in the top-right corner of the page. Proceed to checkout, enter your PayPal account or credit card details and download the STL files.Below you can find printing recommendations for Cura, Simplify3D and Slic3r softwares.Recommendations: For all parts of Locks you need to change "Brim" type to "Skirt" in Build Plate Adhesion section.To avoid printing problems, we recommend the following settings:QualityLayer Height: 0.1 mmInitial Layer Height: 0.3 mmLine Width: 0.4 mm Wall Line Width: 0.4 mm   Outer Wall Line Width: 0.4 mm   Inner Wall(s) Line Width: 0.4 mm Top/Bottom Line Width: 0.4 mm Infill Line Width: 0.4 mm Skirt/Brim Line Width: 0.4 mmSupport Line Width: 0.4 mm Initial Layer Line Width: 100%Shell Wall Thickness: 0.8 mm    Wall Line Count: 2Outer Wall Wipe Distance: 0.2 mmTop Surface Skin Layers: 0Top/Bottom Thickness: 0.8 mm   Top Thickness: 0.8 mm       Top Layers: 8    Bottom Thickness: 0.8 mm      Bottom Layers: 8Top/Bottom Pattern: LinesBottom Pattern Initial Layer: LinesTop/Bottom Line Directions: [ ]Outer Wall Inset: 0 mmCompensate Wall Overlaps: Check    Compensate Outer Wall Overlaps: Check    Compensate Inner Wall Overlaps: CheckFill Gaps Between Walls: EverywhereFilter Out Tiny Gaps: CheckHorizontal Expansion: 0 mmInitial Layer Horizontal Expansion: 0 mmZ Seam Alignment: Sharpest CornerSeam Corner Preference: Hide SeamIgnore Small Z Gaps: CheckExtra Skin Wall Count: 1Infill Infill Density: 20%Infill Line Distance: 4.0 mmInfill Pattern: GridInfill Line Directions: [ ]Infill X Offset: 0 mmInfill Y Offset: 0 mmInfill Overlap Percentage: 10%    Infill Overlap: 0.04 mmSkin Overlap Percentage: 5%    Skin Overlap: 0.02 mmInfill Wipe Distance: 0.1 mmInfill Layer Thickness: 0.1 mmGradual Infill Steps: 1Gradual Infill Steps Height: 1.5 mmInfill Before Walls: CheckMinimum Infill Area: 0 mm2Skin Removal Width: 0.8 mm    Top Skin Removal Width: 0.8 mm    Bottom Skin Removal Width: 0.8 mmSkin Expand Distance: 0.8    Top Skin Expand Distance: 0.8    Bottom Skin Expand Distance: 0.8Maximum Skin Angle for Expansion: 90˚    Minimum Skin Width for Expansion: 0.0Material Initial Layer Flow: 100%Enable Retraction: CheckRetraction Extra Prime Amount: 0 mm3 Retraction Minimum Travel: 0.8 mmMaximum Retraction Count: 90Minimum Extrusion Distance Window: 6.5 mmNozzle Switch Retraction Distance: 16 mmNozzle Switch Retraction Speed: 20 mm/s    Nozzle Switch Retract Speed: 20 mm/s    Nozzle Switch Prime Speed: 20 mm/s Speed Print Speed: 45 mm/s    Infill Speed: 45 mm/s    Wall Speed: 22.5 mm/s      Outer Wall Speed: 22.5 mm/s      Inner Wall Speed: 45 mm/s    Top/Bottom Speed: 15 mm/s    Support Speed: 45 mm/s      Support Infill Speed: 45 mm/sTravel Speed: 45 mm/sInitial Layer Speed: 22.5 mm/s  Initial Layer Print Speed: 22.5 mm/s  Initial Layer Travel Speed: 30 mm/sSkirt/Brim Speed: 45 mm/sMaximum Z Speed: 0 mm/sNumber of Slower Layers: 2Travel Combing Mode: AllAvoid Printed Parts when Traveling: CheckTravel Avoid Distance: 0.6562 mmLayer Start X: 0.0 mmLayer Start Y: 0.0 mmCooling Enable Print Cooling: CheckFan Speed: 100%    Regular Fan Speed: 100%    Maximum Fan Speed: 100% Regular/Maximum Fan Speed Threshold: 10 sInitial Fan Speed: 0%Regular Fan Speed at Height: 0.3 mm    Regular Fan Speed at Layer: 2 Minimum Layer Time: 5 sMinimum Speed: 10 mm/sSupport Generate Support: CheckSupport Placement: EverywhereSupport Overhang Angle: 60°Support Pattern: Zig ZagConnect Support ZigZags: CheckSupport Density: 15 %    Support Line Distance: 2.2 mmSupport Z Distance: 0.13 mm    Support Top Distance: 0.13 mm    Support Bottom Distance: 0.13 mmSupport X/Y Distance: 1 mmSupport Distance Priority: Z overrides X/YMinimum Support X/Y Distance: 0.25 mmSupport Stair Step Height: 0.3 mmSupport Stair Step Maximum Width: 5.0 mmSupport Join Distance: 2.0 mmSupport Horizontal Expansion: 0.2 mmSupport Infill Layer Thickness: 0.1 mmGradual Support Infill Steps: 0Use Towers: CheckTower Diameter: 3.0 mmMinimum Diameter: 3.0 mmTower Roof Angle: 65° Build Plate Adhesion Build Plate Adhesion Type: Brim (for all parts of locks use "Skirt")Skirt/Brim Minimum Length: 250 mmBrim Width: 8.0 mm    Brim Line Count: 15 Brim Only on Outside: CheckMesh Fixes Union Overlapping Volumes: CheckMerged Meshes Overlap: 0.15 mmSpecial ModesPrint Sequence: All at OnceSurface Mode: NormalExperimentalSlicing Tolerance: MiddleMaximum Resolution: 0.01 mmFlow rate compensation max extrusion offset: 0 mmFlow rate compensation factor: 100%Disclaimer: This model will look outstanding if printed on SLA/SLS 3D printer. The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.This model was tested with PLA material.To avoid printing problems, we recommend the following settings:ExtruderNozzle Diameter: 0.4 mmExtrusion Multiplier: 0.97Extrusion Width: AutoRetraction Distance: 5.00 mmExtra Restart Distance: 0.00 mmRetraction Vertical Lift: 0.08 mmRetraction Speed: 5400.0 mm/minWipe Distance: 5.00 mmLayerPrimary Layer Height: 0.2 mmTop Solid Layers: 8Bottom Solid Layers: 5Outline/Perimeter Shells: 2Outline Direction: Inside-OutFirst Layer Height: 90%First Layer Width: 100%First Layer Speed: 20%AdditionsUse Skirt/Brim: CheckSkirt Layers: 1Skirt Offset from Part: 6.00 mmSkirt Outlines: 5InfillInternal Fill Pattern: Fast HoneycombExternal Fill Patern: RectilinearInterior Fill Percentage: 10%Outline Overlap: 22%Infill Extrusion Width: 100%Minimum Infill Length: 5.00 mmCombine Infill Every: 1 layersExternal Infill Angle Offsets: 45/-45 degSupportGenerate Support Material: CheckSupport Infill Percentage: 15%Extra Inflation Distance: 1.00 mmSupport Base Layers: 0Combine Support Every: 1 layersDense Support Layers: 0Dense Infill Percentage: 70%Support Type: NormalSupport Pillar Resolution: 5.00 mmMax Overhang Angle: 60 degHorizontal Offset From Part: 0.50 mmUpper Vertical Separation Layers: 1Lower Vertical Separation Layers: 1Support Infill Angles: 45 degTemperatureExtruder 1 Temperature: 210Heated Bed: 60CoolingIncrease fan speed for layers below: 45.0 sec  Maximum Cooling fan speed: 50%Bridging fan speed override: 100%SpeedsDefault Printing Speed: 4800.0 mm/minOutline Underspeed: 50%Solid Infill Underspeed: 80%Support Structure Underspeed: 80%X/Y Axis Movement Speed: 10800.0 mm/minZ Axis Movemen Speed: 1002.0 mm/minAdjust printing speed for layers below: 15.0 sec   Allow speed reduction down to: 20%OtherUnsupported area threshold: 20.0 sq mLayer height  Layer height: 0.1 mm  First layer height: 90%Vertical shells  Perimeters: 2Horizontal shells  Soid layers:               Top: 8              Bottom: 5Quality  Detect thin walls: Check  Detect bridging perimeters: CheckAdvanced  Seam position: RandomInfill  Fill desity: 20%  Fill pattern: Honeycomb  Top/bottom fill pattern: RectilinearReducing printing time  Combine infill every: 1 layersAdvanced  Solid infill every: 0 layers  Fill angle: 25 deg  Solid infill threshold area: 0mmSkirt  Loops: 2  Distance from object: 6 mm  Skirt height: 1 layers  Minimum extrusion length: 4 mmBrim   Brim width: 10 mmSupport material  Generate support material: Check  Overhang threshold: 45 deg  Enforce support for the first: 3 layersRaft  Raft layers: 0 layersOptions for support material and raft  Contact Z distance: 0.1 mm  Pattern: Rectilinear  Patter spacing: 2 mm  Pattern angle: 0 deg  Interface layers: 2 layers  Interface pattern spacing: 0.2 mmSpeed for print moves  Perimeters: 60 mm/s  Small perimeters: 20 mm/s  External perimeters: 20 mm/s  Infill: 60 mm/s  Solid infill: 60 mm/s  Top solid infill: 30 mm/s  Support material: 50 mm/s  Support material interface: 100%  Bridges: 30 mm/s  Gap fill: 50 mm/sSpeed for non-print moves  Travel: 60 mm/sModifiers  First layer speed: 30 mm/sAcceleration control  Perimeters: 800 mm/s  Infill: 1500 mm/s  Bridge: 1000 mm/s  First layer: 1000 mm/s  Default: 1000 mm/sAutospeed  Max print speed: 100 mm/s  Max volumetrix speed: 0 mm/sExtrusion width  Default extrusion width: 0.42 mm  First layer: 0.42 mm  Perimeters: 0.42 mm  External perimeters: 0.42 mm  Infill: 0.42 mm  Solid infill: 0.42 mm  Top solid infill: 0.42 mm  Support material: 0.42 mmOverlap  Infill/Perimeters overlap: 20%Flow  Bridge flow ratio: 0.95Other  XY Size Compensation: 0 mm  Threds: 8  Resolution: 0 mm