SpoolWorks Scaffold Soluble Support Spool Carrier

prusaprinters

<p>This is a Spool Carrier designed specifically to fit inside the airtight bag used to store E3D's SpoolWorks Scaffold Soluble Support. It will work with all SpoolWorks 200mm Spools (500g/750g) . Supports both 2.85mm &amp; 1.75mm filament.</p> <p>Read the Fulll, detailed, blog post about E3D's Scaffold at | <a href="http://e3d-online.com/Scaffold-Support-Material"> Scaffold Blog Post</a>.</p> <p>Print with your favourite thermoplastic | <a href="http://e3d-online.com/All-Filament">http://e3d-online.com/All-Filament</a></p> <p>Consider the <a href="https://www.thingiverse.com/thing:2339027">Heavy-Duty Air-Tight Filament Spool Case</a> as an alternative.</p> <p>2 x <a href="http://e3d-online.com/608ZZ">608ZZ Bearings</a>.<br/> 1 x <a href="http://e3d-online.com/index.php?route=product/search&amp;search=threaded%20bowden%20coupling">1.75mm or 2.85mm Thread Bowden Coupling</a>.<br/> 1 x <a href="http://e3d-online.com/index.php?route=product/search&amp;search=ptfe%20tubing">Matched Length of PTFE</a>.<br/> 6 x M3 10mm Socket Cap Screws.<br/> 6 x M3 Hex nuts.<br/> 1 x M8 50mm Socket Cap Screw.<br/> 1 x M8 Hex Half Nut.<br/> 1 x M8 Washer.<br/> 1 x Rubber O-Ring 10mm ID x 2.5mm.</p> <p><a href="http://steps-per-mm.xyz"></a> Love 3D printing? Love T-Shirts?</p> <p>Then you need to check out <a href="http://steps-per-mm.xyz">steps-per-mm.xyz</a>!</p> <p>It is loaded with a huge range of wearable Parts &amp; Components.</p> <p>Please help support my work here on <a href="/GregoryHolloway/">Thingiverse</a> and on <a href="https://www.instructables.com/member/SilverJimny/">Instructables</a> by using the following affiliate links when making purchases. Thanks :)</p> <p><a href="https://rover.ebay.com/rover/1/711-53200-19255-0/1?icep_id=114&amp;ipn=icep&amp;toolid=20004&amp;campid=5337999268&amp;mpre=www.ebay.com">eBay.com</a> | <a href="https://rover.ebay.com/rover/1/710-53481-19255-0/1?icep_id=114&amp;ipn=icep&amp;toolid=20004&amp;campid=5337999268&amp;mpre=www.ebay.co.uk">eBay.co.uk</a> | <a href="https://rover.ebay.com/rover/1/709-53476-19255-0/1?icep_id=114&amp;ipn=icep&amp;toolid=20004&amp;campid=5337999268&amp;mpre=www.ebay.fr">eBay.fr</a> | <a href="http://amzn.to/2svRleo">Amazon.co.uk</a></p> <h3>Print instructions</h3><h3>Category: 3D Printer Accessories Print Settings</h3> <p><strong>Printer:</strong> E3D's BigBox</p> <p><strong>Rafts:</strong> No</p> <p><strong>Supports:</strong> No</p> <p><strong>Resolution:</strong> 0.25mm</p> <p><strong>Infill:</strong> 15%</p> <h3> Post-Printing</h3> <p><strong>Using the Carrier</strong></p> <p>Slide the spool onto the carrier and load it into the bag making sure the hole for the bowden coupling is facing towards the bag's opening.</p> <p>Guestimate an approximate place in the bag where it aligns with the hole for the bowden coupling and make a small cut in the bag.</p> <p>Fit the optional O-Ring over the threaded section of the bowden coupling. Screw the coupling into the hole ensuring a good seal.</p> <p>Attach your PTFE to the coupling, feed in some Scaffold and then seal up the bag. Remember to leave the included packet of silica gel in the bag.</p> <p>You're all set!</p> <p>Happy Printing :)</p>