Sony FDR-X3000/X1000 helmet side mount

prusaprinters

<h3>Action camera helmet side holder</h3> <p>I made this holder to be connected directly on helmet by 3M VHB tape or zip tie. However zip ties requires to makes holes into helmet, which is not recommended way (<strong>keep on mind that any modification of your helmet means void of its warranty and have negative impact on helmets protection ability!</strong>).</p> <p>Holder consists of 2 parts so it can be folded when it is not used. Camera is connected over 1/4 stativ screw. Theoretically there can be connected any of FDR Sony action cams, but personally I tested only <a href="http://www.sony.com/electronics/actioncam/fdr-x3000-body-kit">FDR-X3000</a> and <a href="http://www.sony.com/electronics/actioncam/fdr-x1000v-body-kit">FDR-X1000</a>.</p> <p>Just note that the nice helmet in model made by <a href="https://grabcad.com/ivan.spasic--1">Ivan Spasić</a> was loaded from <a href="https://grabcad.com/library/skate-helmet">here</a>.</p> <h3>Additional parts:</h3> <ul> <li>Screw ISO4017 - M5x40</li> <li>Nut ISO4032 - M5</li> <li>1/4 stativ screw (e.g <a href="https://www.fotoskoda.cz/gitzo-d116138-nahradni-sroub/">GITZO D116.138</a>)<br/> ### Changelog:</li> </ul> <p>*<em>25.11.2018</em></p> <blockquote><p>After years of using I found that even smaller holder would be better ;-).</p> <p><br/> *<em>7.1.2017</em></p> <p>After day on snow in mountains I found that stativ screw wrapped by ice made impossible to remove camera from helmet till ice is melt. Therefore I modified screw head. Groves on the side of head was replaced by smooth surface to prevent from locking by ice.</p> <p><br/> *<em>8.12.2016</em><br/> Created first model of holder. Model was successfully tested at home.</p> </blockquote> <h3>Print instructions</h3><h3>Category: Camera Summary</h3> <h3> Action camera helmet side holder</h3> <p>I made this holder to be connected directly on helmet by 3M VHB tape or zip tie. However zip ties requires to makes holes into helmet, which is not recommended way (<strong>keep on mind that any modification of your helmet means void of its warranty and have negative impact on helmets protection ability!</strong>).</p> <p>Holder consists of 2 parts so it can be folded when it is not used. Camera is connected over 1/4 stativ screw. Theoretically there can be connected any of FDR Sony action cams, but personally I tested only <a href="http://www.sony.com/electronics/actioncam/fdr-x3000-body-kit">FDR-X3000</a> and <a href="http://www.sony.com/electronics/actioncam/fdr-x1000v-body-kit">FDR-X1000</a>.</p> <p>Just note that the nice helmet in model made by <a href="https://grabcad.com/ivan.spasic--1">Ivan Spasić</a> was loaded from <a href="https://grabcad.com/library/skate-helmet">here</a>.</p> <h3>Additional parts:</h3> <ul> <li>Screw ISO4017 - M5x40</li> <li>Nut ISO4032 - M5</li> <li>1/4 stativ screw (e.g <a href="https://www.fotoskoda.cz/gitzo-d116138-nahradni-sroub/">GITZO D116.138</a>)<br/> ### Changelog:</li> </ul> <p>*<em>25.11.2018</em></p> <blockquote><p>After years of using I found that even smaller holder would be better ;-).</p> <p><br/> *<em>7.1.2017</em></p> <p>After day on snow in mountains I found that stativ screw wrapped by ice made impossible to remove camera from helmet till ice is melt. Therefore I modified screw head. Groves on the side of head was replaced by smooth surface to prevent from locking by ice.</p> <p><br/> *<em>8.12.2016</em><br/> Created first model of holder. Model was successfully tested at home.</p> <p></p> <h3> Print Settings</h3> </blockquote> <p><strong>Printer:</strong> Rebel II</p> <p><strong>Rafts:</strong> Doesn't Matter</p> <p><strong>Supports:</strong> No</p> <p><strong>Resolution:</strong> 0,4 mm</p> <p><strong>Infill:</strong> 100%</p> <p><strong>Notes:</strong></p> <p>ABS</p>