Soldering Fume Extractor

prusaprinters

<p>This is a 3D printed soldering fume extractor using a 12V PC case fan and USB-C PD board to allow 12V to be provided by a suitable USB-C charger instead of a 12V 'wall wart' adaptor. There are a lot of other 3D printed fume extractors out there but I didn't find any I quite liked, so now there is one more. Of course a lot of it was also about using parts I happened to have laying around.</p> <h3>Print instructions</h3><h3>Bill of Materials</h3> <h3>Fasteners and Electronics</h3> <p>The following non-printed parts are required.</p> <ul> <li><a href="https://www.aliexpress.com/item/4000232858343.html">6 x Brass Hot Melt Inserts - M3x7</a></li> <li><a href="https://www.aliexpress.com/item/4000139809599.html">1 x USB-C PD Board</a></li> <li><a href="https://www.corsair.com/us/en/Categories/Products/Fans/AIR-SERIES-LED-CONFIG/p/CO-9050003-WW">1 x 120x120x25mm 12V DC Fan</a></li> <li><a href="https://www.aliexpress.com/item/32810852732.html">6 x M3x6mm Button Head Hex Screw</a></li> <li><a href="https://www.aliexpress.com/item/33012003529.html">4 x M3 Thin Nut</a></li> <li><a href="https://www.aliexpress.com/item/32810852732.html">4 x M3x30mm Button Head Hex Screw</a></li> <li><a href="https://www.aliexpress.com/item/32691789699.html">1 x 21x15mm SPST Rocker Switch</a></li> <li><a href="https://www.aliexpress.com/item/32514500567.html">4 x Rubber Bumper Feet 10x2mm</a></li> <li><a href="https://www.aliexpress.com/item/32712020268.html">1 x Activated Carbon Filter 130x130x10mm</a></li> <li><a href="https://www.jaycar.com.au/18w-usb-type-c-mains-power-adaptor-with-power-delivery/p/MP3410">1 x USB-PD Charger with 12V capability</a></li> <li><a href="https://www.jaycar.com.au/usb-type-c-to-usb-type-c-cable-1m/p/WC7920">1 x USB-C Cable</a></li> </ul> <p>Most 120mm PC case fans should provide sufficient airflow, however it pays to set first. Power up the fan with the carbon filter in front of it (airflow should be front to back) and do a little soldering and ensure the fumes are pulled in.</p> <p>Ensure the USB-PD charger you select is capable of providing 12V and sufficient current for the chosen fan. The USB-C cable should also be suitable for USB-PD usage.</p> <h3>Printed Parts</h3> <p>The following printed parts are required.</p> <ul> <li>1 x Baffle</li> <li>1 x Fan Housing</li> <li>1 x Rear Panel</li> <li>1 x Stand</li> <li>1 x Base</li> </ul> <p>I printed all but the base at 0.4mm layer height with a 0.8mm nozzle for speed. This resulted in a strong and fast print, if somewhat ugly. Because of the tolerances needed on the base piece for the USB-C PD board I printed the base at 0.2mm layer height with a regular 0.4mm nozzle. Of course, the entire print could be done with these settings too.</p> <p>Supports are not be required. There are a few small bridges and overhangs but nothing major. Note that the rear panel and base of the fan housing and baffle are only 0.8mm thick. This was intentional to speed up printing, however take care not to break any of the parts before assembly.</p> <p>Unsupported holes are closed up, so you will need to take a 3mm drill bit and open them up before using the parts. There is only a 0.4mm thickness to the filled part so it is easy to push the drill bit through. I printed mine in eSUN PLA+ however most filaments should be suitable.</p> <h3>Assembly</h3> <p>After printing insert two brass hot inserts into the fan housing and four into the stand. These can be easily pressed in with a soldering iron, if you want them to be really clean you can use <a href="https://www.tindie.com/products/virtjoule/heat-set-insert-install-4-40-m3-and-m5/">one of these</a>, let them go almost all the way in then turn the print upside down and press it on a flat surface.</p> <p>Cut the connector off the fan and push the cable through the hole in the fan housing. Then push the fan itself into the fan housing, it should just be a tight friction fit. The screws used later are not to hold the fan in but rather to join the front to the back of the housing. Be sure not to pinch the cable.</p> <p>Feed the cable through the hole in the stand, you can then screw the stand to the fan housing using 2 x M3x6mm screws. Place the baffle on the front and push through the four M3x30mm screws. Push the four M3 nuts into the positions on the rear panel and place the rear panel on and gently tighten the screws.</p> <p>Take the base and insert the USB-C PD board. It helps to use a downward angle to line up the connector with the hole. Once lined up push the PCB down against the print. Ensure the lip at the back of the PCB is preventing it from sliding backwards when inserting a cable.</p> <p>You will need to setup the USB PD board for 12V from start up. There is a small switch on the board, hold it down and insert the USB-C cable, connected to a PD capable charger. The LED on the board will cycle rapidly through its colours. Let go of the switch. You can then press the switch to manually cycle through the different colours, each of which represents a different voltage.</p> <p>Press the button until the LED is red, this is the standard 5V setting. Press the switch again, it should switch to yellow (9V), then finally once more and it should switch to green (12V). Now hold the button until the light goes out, then replug the board. It should power up directly in 12V mode. Check this is the case with a multimeter before hooking up the fan. Note that there are quite a few variations of these USB PD boards so check the documentation for your specific one.</p> <p>Before inserting the rocker switch into the stand you'll want to wire everything up, passing the wires needed through the front of the stand. I wired the switch inline with the positive fan cable and positive terminal on the USB PD board. Use your preferred method to hook up everything then screw the base to the stand, taking care to not pinch any wires.</p> <p>After testing to ensure everything works you can install the rubber feet on the base. Finally insert the carbon filter into the front of the baffle, it should be a snug fit and stay in on its own. Switch it on and give it a test to see how it works. Happy soldering!</p> <h3>Source Files</h3> <p>This print was modelled in <a href="https://onshape.com">Onshape</a>. You can access the source files from here:</p> <ul> <li><a href="https://cad.onshape.com/documents/9efcd586e88294096ea0c573/w/6ea79f7a71ab0c3b220eeae0/e/79c82722d3e1283b96f0b40d">Soldering Fume Extractor - Onshape Document</a></li> </ul> <p>These are also released under CC-BY-SA 4.0. If you need to adjust tolerances for your particular fan, switch and USB-PD board.</p>