Snapmaker Artisan CNC Dust cover

thingiverse

Snapmaker Artisan CNC 磁吸快拆吸尘装置 只需打印上下盖板，吸尘罩，固定圈和出风管；穿墙接头按需打印，用于穿越工作台面或外罩，更适合快速替换用于激光吸风装置（后续更新...） 外配件： 外径8mm 厚4mm 孔3mm（厚标称4mm，实测3.6mm）磁铁12~24个（快拆装置12个，穿墙接头12个）。 直径2.6mm长10mm平头自攻螺丝6~10个 直径40mm聚氨酯工业吸风软管2m 宽度25mm硅胶挡风条3m（自带双面胶，实用260mm） 组装：出风管和吸风罩装上磁铁，用自攻螺丝固定，上下盖板磁铁用力按入即可，注意磁铁平面全都朝下，即SN极相吸。硅胶条贴于固定圈上，放入吸尘罩内，组装好吸尘罩，出风管再接上软管并和外置吸尘设备相连接。拆下原CNC执行头的上下盖板，用装好磁铁的打印件替换。 使用：可以先不装吸风装置，原点标定，跑边框等完成后，在开始运行前，升Z轴100mm，装入吸风装置，再降Z轴100mm，并打开外部吸尘装置，下一步就可以正式启动了。 跑边框注意预留集尘罩位置空间，以免加上后撞夹具！切记！！！ 更多功能后续改进更新及升级中... 配套的旋风集尘器 https://www.thingiverse.com/thing:5999277 低成本，低噪音，免维护，经试用反馈效果可行！ ———————————————————————————————————— The following is from Microsoft's machine translation Snapmaker Artisan CNC magnetic quick release vacuum device Just print the upper and lower covers, dust hoods, fixing rings and air outlet pipes; Through-wall fittings are printable on demand for traversing worktops or covers, and are more suitable for quick replacement for laser suction units (to be updated later)... External accessories: Outer diameter 8mm thick 4mm hole 3mm (thickness nominal 4mm, measured 3.6mm) magnets 12~24 (12 quick release devices, 12 through-wall joints). Diameter 2.6mm length 10mm flat head self-tapping screws 6~10pcs Diameter 40mm polyurethane industrial suction hose 2m Width 25mm silicone wind shield 3m (Comes with double-sided tape, practical 260mm) Assembly: The outlet pipe and the suction hood are equipped with magnets, fixed with self-tapping screws, and the upper and lower cover magnets can be pressed in hard, pay attention to the magnet plane are all facing down, that is, the SN pole attracts each other. The silicone strip is attached to the fixing ring, put into the vacuum hood, the dust hood is assembled, the air outlet pipe is connected to the hose and connected to the external vacuum equipment. Remove the upper and lower covers of the original CNC actuator head and replace them with a printed part with a magnet installed. Use: You can first do without the suction device, origin calibration, running frame, etc., before starting the operation, raise the Z axis 100mm, load the suction device, and then lower the Z axis by 100mm, and open the external vacuum device, the next step can be officially started. When running the frame, pay attention to reserve space for the position of the dust cover to avoid adding a rear collision fixture! Remember!!! More featuresFollow-up improvements, updates and upgrades... Matching cyclone dust collector https://www.thingiverse.com/thing:5999277 Low cost, low noise, maintenance-free, trial feedback effect is feasible!