Sice Mosquito/Magnum Precision Piezo Orion Mount

thingiverse

## Precision Piezo Orion Mount for Mosquito/Magnum Hotends Mount the [Slice Engineering](http://sliceengineering.com) Mosquito and Magnum hotends with the [Precision Piezo Orion](https://www.precisionpiezo.co.uk/product-page/precision-piezo-orion-pcb) z-probe. This is the bottom part of the Orion mounting system only - the upper section remains unchanged regardless of the groove mount, direct, or other design. Refer to the official Precision Piezo files at [https://www.thingiverse.com/thing:2841681](https://www.thingiverse.com/thing:2841681) for the remaining part(s). There are multiple variants for mounting the hot end and tensioning the piezo. Two mounting methods are provided - heat set brass inserts or self-threading screws. Although less common, the screws offer a significantly more stable method. The mount can be connected to its base in two ways as well - a traditional, all-printed part and an alternate that uses o-rings to help fine-tune preload and calibrations. More details on the o-ring option are available from the designer ajcraig at [https://www.thingiverse.com/thing:3122283](https://www.thingiverse.com/thing:3122283). STEP files are included. ## Required Hardware | Description | Link | |---------------------------------------- | ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------ | | M2.5 x 4mm Brass Threaded Insert | [https://www.amazon.com/gp/product/B01N8QX6RX](https://www.amazon.com/gp/product/B01N8QX6RX) | | Thread-Forming Screws for Thin Plastic | [https://www.mcmaster.com/96817a894](https://www.mcmaster.com/96817a894) | | Capricorn XS PTFE tubing | [https://www.captubes.com/shop/#!/XS-Series-Ultra-Low-Friction-PTFE-Tubing/c/23214267/offset=0&sort=normal](https://www.captubes.com/shop/#!/XS-Series-Ultra-Low-Friction-PTFE-Tubing/c/23214267/offset=0&sort=normal) | | M3 Bolt | 8, 12, 20mm use spares from Kit or self-source | ## Printing Notes PETG/ABS are preferred materials. To function properly, this portion of the Orion mounting system works best with a small amount of flex. PLA is possible but stiffer than desired. Note that the upper section should be as stiff as possible. Prints without supports. Any supports are likely to get stuck in the small brass insert holes, and internal supports will impede the small amount of flex the Orion needs to function properly. ## Part of the Emma Puggle Railcore II Collection | Description | Link | |----------------------------------------------------------------------------------- | ---------------------------------------------------------------------------------------- | | Railcore II BMG + Precision Piezo Orion - Printed Carriage | [https://www.thingiverse.com/thing:3240565](https://www.thingiverse.com/thing:3240565) | | Railcore II BMG + Precision Piezo Orion - Aluminum Y-Carriage | [https://www.thingiverse.com/thing:3461186](https://www.thingiverse.com/thing:3461186) | | Sice Mosquito/Magnum Precision Piezo Orion Mount | [https://www.thingiverse.com/thing:3456684](https://www.thingiverse.com/thing:3456684) | | E3D v6 Precision Piezo Orion Mount | [https://www.thingiverse.com/thing:3646599](https://www.thingiverse.com/thing:3646599) | | Railcore II Drag Chain | [https://www.thingiverse.com/thing:3582159](https://www.thingiverse.com/thing:3582159) | | Railcore II Aluminum Y Carriage Belt Retainer | [https://www.thingiverse.com/thing:3597877](https://www.thingiverse.com/thing:3597877) | | Railcore II Fan Adapters | [https://www.thingiverse.com/thing:3646685](https://www.thingiverse.com/thing:3646685) | | Railcore II Part Cooling Fan Support Bracket | [https://www.thingiverse.com/thing:3598226](https://www.thingiverse.com/thing:3598226) |