RC Airplane Stand Medium

thingiverse

** Notice: This is a Very Large Print when Finished & Assembled **\r\n** 279 Meters or 85% of 1 Spool **\r\n** Approximately $21.25 @ $25.00 per 1KG Spool **\r\n\r\nThis 3D printed replica stands tall, just like its wooden counterpart available at http://www.foam-flite.com/shop/index.php?id_product=28&controller=product\r\nThe design is a fresh take on the original, with pieces carefully crafted from scratch using images from the website listed above. The plan is to provide detailed lists of all parts, quantities, settings, time, and cost estimates based on $25 spools of filament. Early estimates suggest it will take less than one spool.\r\n\r\nI've listed all required hardware, with bolts costing around $1 at Farm and Fleet.\r\nI purchased 1/4" Carriage Bolts 3" long and cut them to length, my preferred method.\r\n\r\nRequired Hardware \r\n• 4 1/4” x 1 1/4” Carriage Bolts\r\n• 4 1/4” x 1 1/2” Carriage Bolts\r\n• 4 1/4” x 2 1/2” Carriage Bolts\r\n• 12 1/4 - 20 Nuts\r\n• 4 10-24 x 1½” Round Head Bolts\r\n• 2 10-24 Nuts\r\n• 2 10-24 Nylon Lock Nuts\r\n\r\nCA Glue is recommended for use on the split base pieces.\r\n\r\nI'm adding Neoprene Foam to the edges of the arms that touch the plane for added protection.\r\n\r\n16 Different Pieces, some will need to be printed multiple times.\r\n\r\nPrint Speed 2400 mm/min (my preference, not required)\r\nFilament and time are listed for each piece, with multiples requiring multiplication by the count needed.\r\n\r\n** Base - 6 Pieces ** \r\nBase_Outside_P1_V2 (2) - 10327.8 mm - 3 hours 24 minutes\r\nBase_Outside_P2_V2 (2) - 7106.9 mm - 2 hours 22 minutes\r\nBase_Center_left_V2 (1) - 15301.9 mm - 5 hours 12 minutes\r\nBase_Center_right_V2 (1) - 13897.8 mm - 4 hours 44 minutes\r\nBase_Center_Bottom_left_V2 (1) - 8036.2 mm - 2 hours 49 minutes\r\nBase_Center_Bottom_right_V2 (1) - 7225.9 mm - 2 hours 32 minutes\r\n\r\n** Base Total - 79,331.2 mm - 26 hours 49 minutes (24% 1 Spool)\r\n\r\n** ARM (2) - 8 Pieces each Arm **\r\nArm_A_v2 (2) - 9658.6 mm - 3 hours 17 minutes\r\nArm_B_v2 (1) - 8504.0 mm - 3 hours 0 minutes\r\nArm_B_P2 (2) - 2437.6 mm - 0 hours 59 minutes\r\n\r\n** Single Arm Total - 88571.2 mm - 25 hours 37 minutes (26.8% 1 Spool)\r\n\r\n*** Both Arms Total - 177142.4 mm - 51 hours 14 minutes (53.6% 1 Spool)\r\n\r\n** Misc - 2 Pieces **\r\nKnob_large_v3 (12) - 20043.0 mm - 7 hours 45 minutes (all 12 at one time)\r\nKnob_small_v3 (2) - 2135.5 mm - 0 hours 49 minutes (2 at one time)\r\n\r\n** Misc Total - 22178.5 mm - 8 hours 34 minutes (6.7% 1 Spool)\r\n\r\n*** Built Total - 278652.1 mm - 86 hours 37 minutes (84.4% 1 Spool @ $25 - $21.25)\r\n\r\nAll Pieces have been uploaded.\r\n\r\nMore instructions and pictures to come.\r\n\r\nFYI: I'm working on a CG Balance Addon for this stand, check out thing:3168828\r\nhttps://www.thingiverse.com/thing:3168828