Messuhr V2 (20mm) neues Update 16.10.2022

Messuhr V2 (20mm) neues Update 16.10.2022

prusaprinters

<p><strong>Messuhr 20mm&nbsp;</strong></p><p><strong>******************************************************</strong></p><p><strong>Update 16.10.2022</strong></p><p><strong>Das Update beinhaltet 4 neue Dateien.</strong></p><ol><li><strong>Messuhr 20mm 05(16)-Skala</strong> (durch die Anregung des Makes von CHAOSXSPIRIT</li><li><strong>Messuhr 20mm 05(16)-Gehäuse 2</strong> mit verlängertem Zapfen geeignet für Montage mit <strong>M5</strong> <i>DIN 912, DIN 7985, DIN 85 und ähnliche.</i></li><li><strong>Messuhr 20mm 05(16)-Zeiger</strong></li><li><strong>Messuhr20mmStifte4 </strong>um die Gehäusehälften zu verbinden <i>(mit ein wenig Klebstoff)</i></li></ol><p><i>(Die Modifikationen sind auf den Bildern 1 bis 6 zu sehen.)</i></p><p><strong>******************************************************</strong></p><p>Da die Dimension leider sehr klein sind, <strong>sollte die Drucker-Düse nicht größer als 0,4mm</strong> <strong>sein</strong>.</p><p><i>Dies ist eine größere Variante (Gehäuse D 64mm) da die Details bei meinem ersten Entwurf für FDM-Drucker zu klein und nur für RESIN-Drucker geeignet waren.&nbsp;</i></p><p><strong>Montage</strong>:</p><p>Nach dem Druck werden Messstab und Achse in den Körper eingesetzt.</p><p>Anschließend die Skala über die Achse auf den Körper gesetzt, die beweglichen Teile können mit etwas Flüssigseife “<i>gefettet</i>” werden und ein wenig <i>Cyanacrylat</i>-<i>Klebstoff</i> links und rechts zwischen die Gehäuse-hälften zur Verbindung dieser.</p><p>Die 4mm Löcher können bei der Positionierung helfen in dem eine 4mm Schraube eingesetzt wird (kann nach Aushärtung des Klebstoffs wieder entfernt werden).</p><p>Wenn die Montage fertig ist und der Klebstoff getrocknet wird ein kurzes Stück Haushalts-Gummi (<i>zerschnitten, nicht doppelt</i>) mit zwei Knoten versehen (<i>Abstand zwischen den Knoten ca.36 bis 42 mm</i>.)</p><p>Der eine Knoten wird in die kleine Tasche hinter den Schlitz (<i>Rückseite</i>) gedrückt und der andere Knoten bei eingeschobenem Messtab eine halbe Umdrehung um die Welle gezogen und dann durch die Nut in der Welle.</p><p>Jetzt sollte das Teil bereit sein einen Weg von bis 20mm zu messen.</p><p>Die Zahl auf der Skala ist mit 2 zu multiplizieren (6 Skalenwert x 2 = 12 mm)</p><p>--------------------------------------------------------------------</p><p>Google translates.</p><p><strong>Dial indicator 20mm</strong></p><p><strong>******************************************************</strong></p><p>Updated 10/16/2022</p><p>The update includes 4 new files.</p><ol><li><strong>Messuhr 20mm 05(16)-Skala</strong> (by suggesting the make of CHAOSXSPIRIT</li><li><strong>Messuhr 20mm 05(16)-Gehäuse 2</strong> with extended spigot suitable for mounting with <strong>M5</strong> <i>DIN 912, DIN 7985, DIN 85 and similar.</i></li><li><strong>Messuhr 20mm 05(16)-Zeiger</strong></li><li><strong>Messuhr20mmStifte4 </strong>to connect the case halves<i> (with a little glue)</i></li></ol><p><br><i>(The modifications can be seen in pictures 1 to 6.)</i></p><p><strong>******************************************************</strong></p><p>Since the dimensions are unfortunately very small, the printer nozzle should not be larger than 0.4mm.</p><p>This is a larger variant (housing D 64mm) because the details of my first design were too small for FDM printers and only suitable for RESIN printers.</p><p><strong>Assembly</strong>:</p><p>After printing, the dipstick and axle are inserted into the body.<br>Then put the scale over the axis on the body, the moving parts can be "greased" with some liquid soap and a little cyanoacrylate glue left and right between the housing halves to connect them.<br>The 4mm holes can help with positioning by inserting a 4mm screw (can be removed after the adhesive has cured).</p><p>When the assembly is complete and the glue has dried, a short piece of household rubber (cut, not doubled) is tied with two knots (distance between knots approx. 36 to 42 mm.)</p><p>One knot is pressed into the small pocket behind the slot (back) and the other knot, with the measuring stick inserted, is pulled half a turn around the shaft and then through the groove in the shaft.</p><p>Now the part should be ready to measure a travel of up to 20mm.<br>The number on the scale is to be multiplied by 2 (6 scale value x 2 = 12 mm)</p>

Download Model from prusaprinters

With this file you will be able to print Messuhr V2 (20mm) neues Update 16.10.2022 with your 3D printer. Click on the button and save the file on your computer to work, edit or customize your design. You can also find more 3D designs for printers on Messuhr V2 (20mm) neues Update 16.10.2022.