Magnetic Headphone Hook

prusaprinters

<p>This heavy-duty magnetic headphone hook can attach to a table, cabinet, or other surface, to hold your headphones securely when they are not in use.</p> <h3> Specs:</h3> <p><strong>*Dimensions:</strong> 3.00"W x 2.100"D x 1.500"H (assembled, excluding magnets)<br/> <strong>*Volume:</strong> 2.76 cubic inches (both pieces combined, excluding magnets)<br/> <strong>*Weight:</strong> ~0.1 pounds (both pieces combined, excluding magnets)</p> <h3> Files:</h3> <p><strong>*Magnetic base plate:</strong> PTW-00-1-PT-0199 (Hook, Headphones, Magnetic, Base).STL<br/> <strong>*Headphone hook:</strong> PTW-00-1-PT-0200 (Hook, Headphones, Magnetic, Catch).STL</p> <h3> Needed to complete assembly:</h3> <ul> <li>QTY 9-15: 10mm diameter x 2.6mm thick Neodymium Magnets - <a href="http://www.dx.com/p/10-x-3mm-ndfeb-neodymium-magnet-circular-cylinder-diy-puzzle-set-silver-50-pcs-229283#.VOqSt9jnQYI">http://www.dx.com/p/10-x-3mm-ndfeb-neodymium-magnet-circular-cylinder-diy-puzzle-set-silver-50-pcs-229283#.VOqSt9jnQYI</a> (Description says 3mm thick, but are actually 2.6mm) </li> <li>Epoxy: For gluing in magnets </li> <li>ABS Cement / Acetone: For assembly<br/> NOTES:</li> </ul> <hr/> <ul> <li>.STL names do not match .SLDPRT name because Da Vinci will not print file names over 56 characters. </li> <li>.STL files oriented for printing. </li> <li>No supports needed for printing.</li> <li>2Dec2016: Posted small update to the files, to make them fit together a little easier.</li> </ul> <h3>Print instructions</h3><h3>Category: Audio Summary</h3> <p>This heavy-duty magnetic headphone hook can attach to a table, cabinet, or other surface, to hold your headphones securely when they are not in use.</p> <h3> Specs:</h3> <p><strong>*Dimensions:</strong> 3.00"W x 2.100"D x 1.500"H (assembled, excluding magnets)<br/> <strong>*Volume:</strong> 2.76 cubic inches (both pieces combined, excluding magnets)<br/> <strong>*Weight:</strong> ~0.1 pounds (both pieces combined, excluding magnets)</p> <h3> Files:</h3> <p><strong>*Magnetic base plate:</strong> PTW-00-1-PT-0199 (Hook, Headphones, Magnetic, Base).STL<br/> <strong>*Headphone hook:</strong> PTW-00-1-PT-0200 (Hook, Headphones, Magnetic, Catch).STL</p> <h3> Needed to complete assembly:</h3> <ul> <li>QTY 9-15: 10mm diameter x 2.6mm thick Neodymium Magnets - <a href="http://www.dx.com/p/10-x-3mm-ndfeb-neodymium-magnet-circular-cylinder-diy-puzzle-set-silver-50-pcs-229283#.VOqSt9jnQYI">http://www.dx.com/p/10-x-3mm-ndfeb-neodymium-magnet-circular-cylinder-diy-puzzle-set-silver-50-pcs-229283#.VOqSt9jnQYI</a> (Description says 3mm thick, but are actually 2.6mm) </li> <li>Epoxy: For gluing in magnets </li> <li>ABS Cement / Acetone: For assembly<br/> NOTES:</li> </ul> <hr/> <ul> <li>.STL names do not match .SLDPRT name because Da Vinci will not print file names over 56 characters. </li> <li>.STL files oriented for printing. </li> <li>No supports needed for printing.</li> <li><p>2Dec2016: Posted small update to the files, to make them fit together a little easier.</p> <h3>Instructions</h3> <ol> <li>Print the base plate. Trim any flash or wide layers. </li> <li>Place one small drip of epoxy in each hole to receive a magnet. I used 9 magnets, though the plate supports up to 15. </li> <li>Place a magnet in each hole with epoxy. Press on the plate and magnets with a flat surface (e.g. scrap wood) to seat and align all magnets evenly. Part is designed so magnets protrude slightly (0.1mm), for good contact. </li> <li>Let epoxy cure to "full cure" time in instructions, or magnets may pry out prematurely. </li> <li>Print the headphone hook. Trim any flash or wide layers. </li> <li>Assemble the two printed components together, using ABS cement, acetone, or epoxy.</li> </ol> </li> </ul>