Littlejack

prusaprinters

<p>Well I finally finished my Littlejack airship model<br/> from Skies of Arcadia.</p> <p>A very simple guide to help assemble the model.<br/> <a href="https://www.dropbox.com/s/x61a6lo4opgkake/LJ_assembly_guide.pdf?dl=0">https://www.dropbox.com/s/x61a6lo4opgkake/LJ_assembly_guide.pdf?dl=0</a></p> <p>I have tried to make it as easy as I could to print and reduce as much support material needed as possible.</p> <p>Check print settings for method I used to print each part.</p> <h3>Print instructions</h3><p>Below is the print settings I used for each part.<br/> All settings are recommended settings only.</p> <p>Part file name: LJ_anchor.stl<br/> Layer height: 0.15mm ( this can be done in 0.20mm as well)<br/> Supports: No<br/> Raft: No</p> <p>How many<br/> to print: 1</p> <p>========================================</p> <p>Part file name: LJ_cannon.stl<br/> Layer height: 0.15mm ( this can be done in 0.20mm as well)<br/> Supports: No<br/> Raft: No</p> <p>How many<br/> to print: 6</p> <p>========================================</p> <p>Part file name: LJ_fin.stl<br/> Layer height: 0.15mm ( this can be done in 0.20mm as well)<br/> Supports: Yes (build plate only)<br/> Raft: Yes ( 2 layers)</p> <p>How many<br/> to print: 4 (I recommend printing one at a time.)</p> <p>========================================</p> <p>Part file name: LJ_flag.stl<br/> Layer height: 0.15mm ( this can be done in 0.20mm as well)<br/> Supports: Yes<br/> Raft: Yes (2 layers)</p> <p>How many<br/> to print: 1</p> <p>========================================</p> <p>Part file name: LJ_flap_01.stl<br/> Layer height: 0.15mm ( this can be done in 0.20mm as well)<br/> Supports: Yes<br/> Raft: No</p> <p>How many<br/> to print: 1 ( has both needed items in the one model file)</p> <p>========================================</p> <p>Part file name: LJ_flap_02.stl<br/> Layer height: 0.15mm ( this can be done in 0.20mm as well)<br/> Supports: No<br/> Raft: No</p> <p>How many<br/> to print: 1 ( has both needed items in the one model file)</p> <p>========================================</p> <p>Part file name: LJ_harpoon_cannon.stl<br/> Layer height: 0.15mm<br/> Supports: Yes<br/> Raft: No</p> <p>How many<br/> to print: 1</p> <p>========================================</p> <p>Part file name: LJ_main_hull_01.stl<br/> Layer height: 0.15mm ( this can be done in 0.20mm as well)<br/> Supports: Yes<br/> Raft: No</p> <p>How many<br/> to print: 1</p> <p>========================================</p> <p>Part file name: LJ_main_hull_02.stl<br/> Layer height: 0.15mm ( this can be done in 0.20mm as well)<br/> Supports: Yes<br/> Raft: No</p> <p>How many<br/> to print: 1</p> <p>========================================</p> <p>Part file name: LJ_pins.stl<br/> Layer height: 0.15mm ( this can be done in 0.20mm as well)<br/> Supports: No<br/> Raft: Recommended but up to printer</p> <p>How many<br/> to print: 1 ( has both needed items in the one model file)</p> <p>========================================</p> <p>Part file name: LJ_sail_01.stl<br/> Layer height: 0.15mm<br/> Supports: Yes<br/> Raft: Yes</p> <p>How many<br/> to print: 1</p> <p>========================================</p> <p>Part file name: LJ_sail_02.stl<br/> Layer height: 0.15mm<br/> Supports: Yes<br/> Raft: Yes</p> <p>How many<br/> to print: 1</p> <p>========================================</p> <p>Part file name: LJ_sail_03.stl<br/> Layer height: 0.15mm<br/> Supports: Yes<br/> Raft: Yes</p> <p>How many<br/> to print: 1</p> <p>========================================</p> <p>Part file name: LJ_stand.stl<br/> Layer height: 0.2mm ( this can be done in 0.15mm as well)<br/> Supports: No<br/> Raft: No</p> <p>How many<br/> to print: 1</p> <p>========================================</p> <p>Part file name: LJ_vent_pipe.stl<br/> Layer height: 0.15mm ( this can be done in 0.20mm as well)<br/> Supports: No<br/> Raft: No</p> <p>How many<br/> to print: 1</p> <p>========================================</p>