Jumbo Christmas - Elves - Bernard and Twinkle

thingiverse

I compiled these two elves to go along with my Santa (https://www.thingiverse.com/thing:3899272) and Mrs Claus (https://www.thingiverse.com/thing:2843428) jumbo figures - Bernard is the head elf and Twinkle is the decorator! Used Skimbal's and CountSpatula's figures - a combination of each - at 75% of the jumbo figure size, or 300% of the original minifig size, so they are a bit smaller as elves should be! Printed using Simplify3D in order to pause the print and filament swap where required on the legs. Some of the parts are a bit finicky as they are so small - one of these was the mouth and eyes of the innie-head (https://www.thingiverse.com/thing:1675494) - I actually ended up melting a spare piece of black filament and squishing it into the indents, then sanding flush with the face. Bernard's shirt bottom and Twinkle's zig-zag skirt, their neck cuff and arm cuffs were an afterthought, based on a picture I saw - I compiled these in Sketchup (still learning) and they turned out great! Elf - Bernard ------------- Bernard, being one of the hardest workers and master elf, is serious; nothing else, just plain serious... Bernard's legs were printed using brown, white, red and green ABS filament. Filament swaps were done as follows - each stripe is 2mm thick: Layer 001-048 in brown (the shoe part) Layer 049-058 in white Layer 059-068 in red Layer 069-078 in white Layer 079-088 in red Layer 089-098 in white Layer 099-108 in red Layer 109-118 in white Layer 119+ in green Other colours used are: Shoes - brown (with a couple of gold BB pellets for the shoe bells) Hips - green Body Fringe/Waist - brown (or print a normal body and a brown 1mm thick belt) Buckle - gold Body - green Arms - green Neck Ring and Cuffs - red Hands - Skin Head and Ears - skin Hat Rim - green Hat Top - red or gold Mouth and Eyes - black Extras ------ Bernard's Decoration String -- Lindt chocolate bunny ribbon and 3 Lindt bells - tie-off the bells at the spacing you wish to use and place a dab of glue in each hand to secure. Twinkle's Scroll (https://www.thingiverse.com/thing:2601645) - I printed this in two halves, orientated on the build plate down the middle, as I wanted brown ring pieces and a white scroll paper. Print what you want to put on the scroll on a label sheet - the label cut-out size is 24mm height by 30mm width. Make it central and stick down. The balls on the ends of the shoe tips are yellow gas-gun air pellets that I had lying around. There is no .stl included, but you could source something from Thingiverse if needed, although at 75% scaling they may be difficult to print. REMEMBER: some of the files are still sized at 400% for the jumbo 4x figures - I printed some parts at 75% and others at 300%, depending on the source file size. You should be able to gauge for yourself which parts should be printed at what size. UPDATE: 30 NOV 2018 ================== Per request, I have added 3 additional .STL files for: - the left and Right ears only (Skin_Ears_L_R Only.stl) - single head with the left and right ears (Skin_Heads_and_Ears_1xHead_with_Ears.stl) - 2 heads with the 2 sets of left and right ears -- removed the extra heads below the print bed, so this STL effectively replaces file Skin_Heads_and_Ears_Z_TO_ZERO.stl (Skin_Heads_and_Ears_2xHeads_4xEars.stl) NB: check that the parts sit flat on the print bed. Adjust positioning in your slicer if needed. Please check/feedback whether they work for you - I have not tested and am not too good with Meshmixer yet!