Hotwheels Lancia Stratos Group 5 Display Base

prusaprinters

<p>There is also a standard Stratos base back wall design included too.</p><p>There are multiple variants of Lancia Stratos for this size, the Hotwheels Group 5 is the only one I have but If you have other variants, I could make another base to fit it. I need the length and width of the car base as shown here: <a href="https://imgur.com/5T6mb2L">https://imgur.com/5T6mb2L</a></p><p>The display base is separated into 3 parts for easy printing and colour swap. The parts are:</p><p>1) Name plate (NamePlateAssem.STL and NamePlateAssem (Stratos Only).STL)<br>2) Base (BaseV2.STL)<br>3) Base back wall (BoxBackAssem.STL and BoxBackAssem (Stratos Only).STL)</p><h3>Base Back Wall and Name Plate Variant</h3><p>There are 2 variants of Base back wall, the one in my pictures are "BoxBackAssem".</p><p>The difference for each base are:</p><h3>BoxBackAssem:</h3><p>As seen in the pictures above, vehicle name "Stratos Group 5" is written on it.</p><h3>BoxBackAssem (Stratos Only):</h3><p>Similar to the on in the picture but with slightly larger "Stratos" and without "Group 5", so it can be used on other Stratos variant</p><p>There are 2 variants of Name Plate, the one in my pictures are "NamePlateAssem".</p><p>The difference for each name plate are:</p><h3>NamePlateAssem:</h3><p>As seen in the pictures above, vehicle name "Stratos Group 5" is written on it.</p><h3>NamePlateAssem (Stratos Only):</h3><p>Similar to the on in the picture but without "Group 5", so it can be used on other Stratos variant</p><h3>Print Settings</h3><p>Nozzle size = 0.4 mm (minimum, smaller better)<br>Layer height = 0.2 mm</p><p>Filament change layer for colours on "BoxBackAssem" &amp; "BoxBackAssem (Stratos Only)":<br>1) Start (Background colour, mine is in white)<br>2) Layer 19 (Lower stripe colour, mine is in green)<br>3) Layer 24 (Upper stripe colour, mine is in red)<br>4) Layer 29 (Lancia logo background colour, mine is in blue)<br>5) Layer 34 (Lancia logo pattern and lettering, mine is in white)<br>6) Layer 39 ("Stratos" and/or "Group 5" lettering colour , mine is in black)</p><p>Filament change layer for colours on "NamePlateAssem" &amp; "NamePlateAssem (Stratos Only)":<br>1) Start (Background colour, mine in white)<br>2) Layer 8 (Lower stripe colour, mine is in green)<br>3) Layer 13 (Upper stripe colour, mine is in red)<br>4) Layer 19 ("Lancia", Stratos and/or "Group 5" lettering colour, mine is in black)</p><h3>Assembly</h3><p>The car is tied by wires through the hole in the base</p><p>Back plate and name plate should slide in nicely into the display base. If the name plate is loose, double sided tape will hold it nicely</p><h3>Others</h3><p>I did not test the "Stratos Only" base back wall and name plate but it should works fine.</p><p>Feel free to send me any feedback on how to improve the design. Suggestion on display base designs are welcomed too.</p><p>I can be contacted through Instagram or Twitter too:</p><p>Twitter: <a href="https://twitter.com/Giga_Penguin">https://twitter.com/Giga_Penguin</a><br>Instagram: <a href="https://www.instagram.com/GigaPenguin3DPrinting/">https://www.instagram.com/GigaPenguin3DPrinting/</a></p>