Garden Irrigation Spray System - Garten Bewässerung System

prusaprinters

<p>Hi</p> <p>here you will find a garden irrigation system like the manufacturer gardena has. Free under the motto "Why buy, when you can print it" ;-) I have designed it modularly and as GlueEdition so that you can connect different ground holders, middle parts with 1-3 direct connections / gardena coupling or different spray heads. the spray heads are still in development. However, angles of 45°, 180°, 270° and 360° are still available. I was amazed how far the spray head sprays with 2.5 - 3 bar water pressure, so a dosage with a screw in the head is available.</p> <p>Preview:</p> <figure class="media"> <oembed url="https://www.youtube.com/embed/ruUPSK0xpcE"></oembed> </figure> <p>Support material:</p> <p>The support material for the spray head is already included in the stl files ( please print the head upside down ). The fine tubes at the place where the o-ring goes in and at the spray exit is can be easily cut out with a cutter knife.<br/> For the middle section only support material is required from the base plate.</p> <p>You need:<br/> Printed parts ;-)<br/> Screws 3,5 x12 or 3,5x15<br/> O-ring inner diameter Ø 12 x 3,5 mm NBR 70 (<a href="https://www.ebay.de/itm/401009056492">https://www.ebay.de/itm/401009056492</a> )<br/> M4x 25mm dosage screw</p> <p>Please note that the development is still in progress. So stay tuned!!!!</p> <hr/> <p><strong>Update 18.05.20</strong></p> <ul> <li>Now there is a middle section "T" with 3 feed lines offset at 90° to each other as a glued edition. With this you can also place a sprinkler on a side of a bed and u can connect a 90° supply line.<br/> <strong>Added:</strong></li> <li>middle_section_3con180_v1_GLUE.stl</li> <li>middle_section_3con180_v1.stl</li> </ul> <p><img alt="" src="https://media.prusaprinters.org/thumbs/cover/125x100/media/prints/864/images/314333_82da8836-4815-47d5-82a9-2f6c10b63824/image-6.jpg"/></p> <p><img alt="" src="https://media.prusaprinters.org/thumbs/cover/125x100/media/prints/864/images/313777_33d58700-6e83-48ea-9384-78f099651b70/image-3.jpg"/></p> <hr/> <hr/> <p><strong>Update 25.04.20</strong></p> <ul> <li>Now there is a middle section with 2 feed lines offset at 90° to each other as a glued edition. With this you can also place a sprinkler in a corner of a bed and you will not have any problems with the supply lines.<br/> <strong>Added:</strong></li> <li>middle_section_2con90_v1_GLUE.stl</li> </ul> <p><img alt="" src="https://media.prusaprinters.org/thumbs/cover/125x100/media/prints/864/images/302683_96a265f9-91a5-4ca3-87ab-a5c7a7329547/middle_section_2con90_v1_glue.jpg"/></p> <hr/> <hr/> <p><strong>Update 31.08.18</strong></p> <ul> <li>From now on there is a spray head with two 90° opposite exits as some people want. This means that even things opposite each other can be cast.<br/> <strong>Added:</strong></li> <li>sprayhead_v2_9090dg.stl</li> <li>sprayhead_v2_9090dgNOdosage.stl</li> </ul> <hr/> <hr/> <p><strong>Update 30.08.18</strong></p> <ul> <li>A GlueEdition is now available. With this, the connections can now be glued to the centre section using acetone. This has two advantages. Anyone can fit any center section with a connector and there is no need to print overhangs. ( No more support needed for the middle section)<br/> I have attached some more pictures of the GlueEdition, which I have already tested. Works out great in my opinion.<br/> <strong>Added:</strong></li> <li>middle_section_1con_GlueEdition_v1.stl</li> <li>middle_section_2con_GlueEdition_v1.stl</li> <li>middle_section_3con_GlueEdition_v1.stl</li> <li>middle_section_GE_Connector_Gardena_v1.stl</li> <li>middle_section_GE_Connector_Hoseclip_v1.stl</li> <li>sprayhead_v1_BlindPlug.stl</li> </ul> <hr/> <hr/> <p><strong>Update 11.07.18</strong></p> <ul> <li>There is now 2 versions of the middle section with clamp connection and Gardena connection, which can be plugged onto a 12mm rod. This means that also higher plants can be sprayed.<br/> <strong>Added:</strong></li> <li>middle_section_StaffHolder_Hoseclip_v1.stl</li> <li>middle_section_StaffHolder_Gardena_v1.stl</li> </ul> <hr/> <hr/> <p><strong>Update 03.07.18</strong></p> <ul> <li>I have added some gardena coupling versions to the middle sections.<br/> <strong>Added:</strong></li> <li>middle_section_1con_1gardena_v1.stl</li> <li>middle_section_2gardena_v1.stl</li> <li>middle_section_1gardena_v1.stl</li> </ul> <hr/> <hr/> <p><strong>Update 26.06.18</strong></p> <ul> <li>I have attached some more pictures of the working system.</li> <li>I make the ground holder still a little stronger and with cross struts.</li> <li>Now the spray head is available with and without dosing screw.<br/> <strong>Added:</strong></li> <li>ground_holder_v2.stl</li> <li>sprayhead_v2_90dgNOdosage.stl</li> <li>sprayhead_v2_180dgNOdosage.stl </li> <li>sprayhead_v2_270dgNOdosage.stl</li> <li>sprayhead_v2_360dgNOdosage.stl</li> </ul> <hr/> <hr/> <p><strong>Update 15.06.18</strong></p> <ul> <li>I have added 90°, 180°, 270°, 360° versions and a dosage option with a screw in all spray heads.<br/> <strong>Added:</strong></li> <li>sprayhead_v2_90dg.stl</li> <li>sprayhead_v2_180dg.stl</li> <li>sprayhead_v2_270dg.stl</li> <li>sprayhead_v2_360dg.stl</li> </ul> <hr/> <p><a href="https://www.thingiverse.com/thing:2958870">https://www.thingiverse.com/thing:2958870</a></p> <p><strong>ALSO INTERESTING</strong></p> <p><a href="https://www.prusaprinters.org/prints/18352"><img alt="" src="https://media.prusaprinters.org/thumbs/cover/170x100/media/prints/18352/images/178509_007b3fa9-fca0-42b0-8234-00fcd1017d20/20191002_222928-02.jpeg"/></a> <a href="https://www.prusaprinters.org/prints/16879"><img alt="" src="https://media.prusaprinters.org/thumbs/cover/170x100/media/prints/16879/images/161706_3ee29b9a-7bb6-4745-bcb5-b192549feda5/20191218_172536.jpg"/></a> <a href="https://www.prusaprinters.org/prints/864"><img alt="" src="https://media.prusaprinters.org/thumbs/cover/170x100/media/prints/864/images/5511_3da6a33d-d23a-4475-85a2-5fe4070371b6/133dd6d2536c9a4998500d6a03c23811_preview_featured.jpg"/></a></p> <p><strong>Happy printing</strong></p> <p>MFG</p> <p>Chris</p> <p><em>Follow me on...</em><br/> <img alt="" src="https://www.prusaprinters.org/assets/favicons/favicon-16x16.png"/> <a href="https://www.prusaprinters.org/social/391-schiffer-softde">prusaprinters.org</a><br/> <img alt="" src="https://cdn.thingiverse.com/site/img/favicons/favicon-16x16.png"/> <a href="https://www.thingiverse.com/schiffer-soft">thingiverse</a><br/> <img alt="" src="http://schiffer-soft.de/api/instagram/insta16x16.png"/> <a href="https://www.instagram.com/schiffer_soft">Instagram</a></p> <p>If you like it ;) - Thx for me!<br/> <img alt="" src="http://schiffer-soft.de/api/paypal/paypal16x16.png"/> <a href="https://www.paypal.me/schiffersoft">www.paypal.me/schiffersoft</a></p>