Frenzy Brick "Prusa Lover"

prusaprinters

<p><strong>This brick is for all Prusa lovers...</strong></p> <p>... but especially for <a href="denied:%E2%80%9Chttp://filamentfrenzy2.wixsite.com/filamentfrenzy%E2%80%9C">Tom Jackson</a> (@FilamentFrenzy on Twitter) and his brick wall.</p> <p>You can choose between two versions of this brick:</p> <ul> <li>Prusa Lover with Daffodil (V01)</li> <li>Prusa Lover with spinning sun (V02)</li> </ul> <p><strong>Instructions:</strong></p> <p><strong>Prusa Lover Daffodil</strong></p> <p>Print each one of these files (no supports needed):</p> <ul> <li>Brick_V01</li> <li>Calyx_V01</li> <li>Petal_01_V01</li> <li><p>Petal_02_V01<br/> The brick is printable in two colors by performing a filament swap at layer height 14.2 (if printed with 0.2 layer height).</p> <p>If you don't know how to set filament swaps in your slicer, feel free to watch my tutorials about it:<br/> <a href="https://youtu.be/i9IEojl87tI">https://youtu.be/i9IEojl87tI</a><br/> <a href="https://youtu.be/RZgDdki_ZHk">https://youtu.be/RZgDdki\_ZHk</a></p> <p>The Calyx is a solid body and should be printed in vase mode.<br/> Alternatively you can print it without infill and without top layers.</p> <p>Print both petal files.</p> <p>Put the petal files over the backside of the calyx and arrange them in a way, that the lower ones lay between the upper ones.<br/> Shape the petals a little bit with a hair dryer or a lighter towards the calyx. (You can see the method in my Water Lily video: <a href="https://youtu.be/jGzSN1bL93I">https://youtu.be/jGzSN1bL93I</a> )<br/> Be careful that you don't melt the calyx or fuse the petals with the calyx, as they should be able to spin freely.</p> <p>Glue the calyx (with the petals attached, but don't put glue on the petals!) into the hole in the brick.</p> </li> </ul> <p><strong>Prusa Lover spinning sun</strong></p> <p>Print each one of these files (no supports needed):</p> <ul> <li>Brick_V02</li> <li>Disk_V02</li> <li>Stick_V02</li> <li>Sun_inner_V02</li> <li><p>Sun_outer_V02<br/> The brick is printable in two colors by performing a filament swap at layer height 14.2 (if printed with 0.2 layer height).</p> <p>The Disk is also printable in two colors by performing a filament swap at layer height 2.2 (if printed with 0.2 layer height).</p> <p>Print the stick and glue it into the hole on the backside of the Disk.</p> <p>Print Sun inner and put it over the stick.<br/> Print Sun outer and put it over the stick.</p> <p>Glue the stick (with the sun parts attached, but don't put glue on them!) into the hole in the brick.</p> </li> </ul> <p><strong>That's it!</strong></p> <p><strong>Have fun with these bricks!</strong></p> <h3>Print instructions</h3><h3>Category: Art Print Settings</h3> <p><strong>Printer Brand:</strong> Prusa</p> <p><strong>Printer:</strong> <a href="http://amzn.to/2rqZ6Uo">i3 MK3</a></p> <p><strong>Rafts:</strong> No</p> <p><strong>Supports:</strong> No</p> <p><strong>Resolution:</strong> 0.2</p> <p><strong>Infill:</strong> 20% (0% Calyx)</p>