Ford FlatHead V8 (12/14) / Transmission extension

thingiverse

This is a Transmission Extension for the Ford FlatHead V8, a highly complex remix of "1939 Ford Toploader Transmission by skipstitch". It consists of 19 intricately designed pieces, with the release shaft functioning as expected and the drive shaft turning smoothly on bearings. # Print Settings 1 x Transmission Body: Layer: 0.15mm, Raft: No, Brim: No, Support: Yes, Infill: 15% 1 x Transmission Body Gasket: Layer: 0.15mm, Raft: No, Brim: No, Support: No, Infill: 100% 1 x Transmission Cover 1: Layer: 0.15mm, Raft: No, Brim: No, Support: No, Infill: 20% 1 x Transmission Cover 1 Gasket: Layer: 0.15mm, Raft: No, Brim: No, Support: No, Infill: 100% 1 x Transmission Cover 2: Layer: 0.15mm, Raft: No, Brim: No, Support: No, Infill: 100% 1 x Transmission Front Main Drive Bearing: Layer: 0.15mm, Raft: No, Brim: No, Support: Yes, Infill: 100% 1 x Transmission Gear Shift: Layer: 0.15mm, Raft: No, Brim: No, Support: Yes, Infill: 100% 1 x Transmission Knob: Layer: 0.15mm, Raft: No, Brim: No, Support: No, Infill: 100% 1 x Transmission Lever: Layer: 0.15mm, Raft: No, Brim: No, Support: Yes, Infill: 100% 1 x Transmission Main Drive Gear: Layer: 0.15mm, Raft: No, Brim: No, Support: Yes, Infill: 80% 1 x Transmission Purge: Layer: 0.15mm, Raft: No, Brim: No, Support: Yes, Infill: 100% 1 x Transmission Purge Gasket: Layer: 0.15mm, Raft: No, Brim: No, Support: No, Infill: 100% 1 x Transmission Rear Trans Mounts: Layer: 0.15mm, Raft: No, Brim: No, Support: Yes, Infill: 20% 1 x Transmission Release Bearing Hub: Layer: 0.15mm, Raft: No, Brim: No, Support: Yes, Infill: 100% 1 x Transmission Release Shaft Fork 1: Layer: 0.15mm, Raft: No, Brim: No, Support: No, Infill: 100% 1 x Transmission Release Shaft Fork 2: Layer: 0.15mm, Raft: No, Brim: No, Support: Yes, Infill: 100% 1 x Transmission Release Shaft Fork Left: Layer: 0.15mm, Raft: No, Brim: No, Support: No, Infill: 100% 1 x Transmission Release Shaft Fork Right: Layer: 0.15mm, Raft: No, Brim: No, Support: No, Infill: 100% 1 x Transmission Screw: Layer: 0.15mm, Raft: No, Brim: No, Support: Yes, Infill: 100% # Accessories 4 x 4mmx2mm disk magnet 6 x m3 threaded insert 1 x m3x73mm threaded rod 1 x m3x65mm rod 2 x m3x1mm SHCS (cut m3x3mm) 10 x m3x5mm SHCS 16 x m3x8mm SHCS 1 x m3x5mm set screw 2 x m3 jam nut 3 x m3 washer 2 x 6702zz bearing 2 x 623zz bearing 1 x pencil spring # Mounting Examine the images for installation instructions.