Estes Pathfinder (kit# 1997)

thingiverse

Here are all of the 3D models you'll need in order to build and fly the Estes Pathfinder kit (#1997). it was produced and sold from 1998 to 1990. STL parts supplied: 1) Fin can #1a - Cruciform (This will slide over the BT-60 tubing.) 2) Fin can #1b - Tri-form (This will slide over the BT-60 tubing.) 3) 5.5 inch (139.7mm) length x BT-60 (OD) fin can 2a (cruciform) (Integrated tubing coupler.) *Adjust airframe tubing length from 18 inches to 12.5 inches (317.5mm)* 4) 5.5 inch (139.7mm) length x BT-60 (OD) fin can 2b (tri-form) (Integrated tubing coupler.) *Adjust airframe tubing length from 18 inches to 12.5 inches (317.5mm)* 5-6) Motor mount rings for 24mm motors that will fit inside fin can 2a and 2b. *Estes BT-50 tubing will fit within these rings.* 7) Fin (if you want to print fins and use them on your rocket.) 8) Fin with TTW (through the wall) tab 9) Fin with TTW (through the wall) tab Version 2 with slot to accommodate motor mount ring. 10-11) BT-60 to BT-50 Motor Mount Rings *To be used with Estes tubing.* 12) BT-50/24mm motor mount block ring 13) Estes PNC-55AO Nose Cone https://www.thingiverse.com/thing:4554882 14) BT-60 to BT-55 Reducer/Transition https://www.thingiverse.com/thing:4962698 Kit Part Extras: 1)Simulated nozzles https://www.thingiverse.com/thing:1243029 https://www.thingiverse.com/thing:4119920 https://www.thingiverse.com/thing:4497043 2) BT-50/24mm Motor Retainer (screw-on) https://www.thingiverse.com/thing:4058299 Non-part Extras: 1) Fin slot cutting guide Cruciform (Can be used as a fin marking guide.) 2) Fin slot cutting guide Tri-form (Can be used as a fin marking guide.) 3) Fin Making Template (To be used with balsa, bassword or other material to make your fins.) 4-5) BT-60 to BT-50 Motor Mount Ring making templates (A and B) 6) Fin alignment guide Parts you will need to supply: 1) Estes BT-50 x 2.75 inch (69.85mm) length tubing (for the 24mm motor mount tube) 1) Estes BT-55 tubing; 18 inch (457.2mm) length 2) Estes BT-60 tubing; 18 inch (457.2mm) length 3) Recovery System: A) 2 x 12" (304.8mm) diameter hexagon parachutes 1.25mil thickness LDPE plastic B) Shock cord mount (JimZ website kit instructions) https://www.spacemodeling.org/jimz/est1997.htm C) Shock cord 18" (457.2mm) length D) Shroud lines 6 x 18" (457.2mm) length 4) Decals (JimZ website with use of decal paper. https://www.spacemodeling.org/jimz/est1997.htm Upscale decals: https://stickershock23.com/product/estes-pathfinder/ 5) 1/8 inch (3.175mm) thick balsa (if you are making your own fins) 6) Fin and launch lug marking guide (JimZ website kit instructions) https://www.spacemodeling.org/jimz/est1997.htm 7) Launch lug for 3/16 inch (4.76mm) launch rod