Dust Cyclone Stabilizer

prusaprinters

<h5><strong>Object description:</strong></h5><p>This assembly stabilizes a cyclone and protects it from breaking off from the collection container due to too much pull on the suction hose.</p><p>&nbsp;</p><h5><strong>Comments:</strong></h5><ul><li>Don't be fooled by the attached photo. All the dust on the cyclone comes from outside. The photo was taken after a few days in hard use in a very dusty environment.</li><li>The cyclone has an efficiency of almost 100%. This means that almost everything ends up in the dust container and the filter in the vacuum cleaner stays clean for a long time.</li></ul><p>&nbsp;</p><h5>Assembly instruction:</h5><ul><li>Melt the thread inserts into the <i>base flange</i></li><li>Screw the <i>feets </i>with the countersunk screws on the <i>ribs</i></li><li>Move the <i>ring </i>over the cyclone</li><li>Apply silicone between base flange and the cyclone</li><li>Put the cyclone on the <i>base flange</i></li><li>Screw the pre-assembled <i>ribs with M4x12mm socket head screws </i>on the <i>base flange</i></li><li>Move the <i>ring </i>down over the pins of the <i>ribs</i></li><li>Apply silicone between <i>base flange</i> and the dust collector</li><li>Screw the stabilizer with M5x20mm,M5 washers and M5 Nuts on the cover of your dust collector</li><li>In the <i>base flange</i>, <i>rib</i> and <i>ring</i> are slots that you can fix the parts together with zip ties, if you want. But this is not necessary.</li></ul><p>&nbsp;</p><h5>Bought parts:</h5><ul><li>1x Cyclone to which the stabilizer fits (size 1): <a href="https://www.amazon.de/dp/B07RWTBDKS/ref=cm_sw_r_wa_api_glt_i_EC2E5YMM1WFNMVRSMHQ8?_encoding=UTF8&amp;th=1">https://www.amazon.de/dp/B07RWTBDKS/ref=cm_sw_r_wa_api_glt_i_EC2E5YMM1WFNMVRSMHQ8?_encoding=UTF8&amp;th=1</a></li><li>8x Thread insert M4 (e.g. <a href="https://www.amazon.de/dp/B07YSV66Y5/ref=emc_b_5_t?th=1">https://www.amazon.de/dp/B07YSV66Y5/ref=emc_b_5_t?th=1</a>)</li><li>8x Socket head screw M4x12mm</li><li>4x Countersunk screw 3x25mm</li><li>16x Washer for M5</li><li>8x Socket head screw M5x20mm</li><li>8x Nut M5</li><li>Silicone or any other sealant to tighten the sealing surfaces</li><li>My airtight dust container: <a href="https://www.amazon.de/dp/B00CHKS59E/ref=cm_sw_r_wa_apa_glt_i_YF9TQ0XKCD0NN0SBF1AD?_encoding=UTF8&amp;psc=1">https://www.amazon.de/dp/B00CHKS59E/ref=cm_sw_r_wa_apa_glt_i_YF9TQ0XKCD0NN0SBF1AD?_encoding=UTF8&amp;psc=1</a><ul><li>Any other airtight sealable container will work as well</li></ul></li></ul><p>&nbsp;</p><h5><strong>Print settings:</strong></h5><p>Material: PLA, PETG or ABS/ASA</p><p>Layer height: 0,2mm</p><p>Infill: 25%</p><p>Perimeters: 3</p><p>Brim: no</p><p>Support: no</p>