Droideka 3D Printing Model | Assembly + Action

gambody

ABOUT THIS 3D MODELDroidekas are a type of dangerous and deadly droids of the Separatist/CIS army that dramatically roll themselves into a battle and guarantee a merciless attack on the opponents. Unlike Battle Droids that were produced in millions of copies, the Destroyers are far more expensive and extremely effective thanks to their impressive defensive and offensive armament. While standing on its three sharp legs the Droideka can simultaneously utilise its personal deflector shield generator and fire at a target using two twin repeating blaster cannons! After that, the Droideka can swiftly curl into a ball and travel to the next target at a surprisingly rapid pace. The manner of Destroyers’ transformation and transit earned droids the “Rollies” nickname and the reputation of formidable and murderous enemies to stand against. The author of the fantastic Droideka model for 3D printing reportedly dedicated circa 150 hours for the iconic Destroyer to roll into the 3D printed collections of Star Wars fans. Similarly to its on-screen counterpart, the 3D printing Destroyer Droid is heavily armed, carrying twin high-energy blasters on each of its arms. The slim sensor head is equipped with a pair of non-visual composite radiation sensor antennas and a single primary sensor antenna that vaguely resemble the robot’s eyes and nose. The round Droideka’s backshell plate looks perfectly ready to furl into a compact wheel in a matter of seconds making the Destroyer a smaller and speedier target for the opponents. The 3D artist also made sure to equip the droid with the deflector shield projector plates, making the Droideka almost invincible to be defeated by an unprepared brave spirit. Boasting the one-of-a-kind silhouette, the Droideka 3D printing model will become a unique piece of Colicoids’ technology on your display shelf! ADAPTATION FOR 3D PRINTINGDroideka model for 3D printing is a highly articulated action assembly model and its moderation and adaptation for different types of 3D printers took Gambody team 48 hours in total. In order to ensure the transformation and multidirectional movement of the Destroyer, it was divided into many assembly parts and special mechanisms were introduced into all model’s joints to give you an opportunity to display the droid in a variety of positions, i.e. its backshell plate, sternum plate, censor head, spinal power cell series, twin high-energy blasters, shield plates, legs, foot claws, etc. come as separate assembly parts. The pistons (arm extensor struts) on Droideka’s arms and the neck are retractable. For you to introduce hydraulic cables that connect the Droideka’s parts in the model’s FFF/FDM 1.0 version we recommend that you use the 1.75mm PLA filament and insert its pieces into designated holes that are designed to fit securely the diameter. The assembly of some of Droideka’s parts (like deflector shield projector plate) requires additional “pins”. These pins do not come in STL files as well but can be made out of short pieces of regular 1.75 PLA. All assembly parts are provided in STL files in recommended positions that were worked out in order to ensure the smoothness of the details’ surfaces after printing and so that the 3D printing beginners won't face difficulties when placing the parts on a build plate. The joints that ensure the droid’s movability and transformation are provided as separate files as well for you to be able to print them again if the joints' friction happens to lose rigidity. The cutting in the droid's FFF/FDM and DLP/SLA/SLS versions was made taking into account the peculiarities of each 3D printing technology. We highly recommend that you watch "Assembly video" in the photo preview section before assembling the Droideka. When downloading any model's file you will also receive "Assembly Manual" for FFF/FDM 1.0 and DLP/SLA/SLS 1.0 versions in PDF format.The model is saved in STL files, a format supported by most 3D printers. All STL files for 3D printing have been checked in Netfabb and no errors were shown.The model's scale was calculated from Droideka​​​'s actual height that is 1750 mm. The 3D printing model's chosen scale is 1:8 for the FFF/FDM version and 1:16 for the DLP/SLA/SLS version.VERSION SPECIFICATIONSFFF/FDM 1.0 version features:- Contains 47 parts;- A printed model is 228 mm tall, 156 mm wide, 192 mm deep;- Droideka can be transformed into a ball;- Each droid's joint (head, neck, "pelvis", sternum, shoulder, elbow, wrist, hip, knee, and shields) is articulated which allows the model's multidirectional movement and transformation;- This version's assembly requires additional “pins” to secure the parts. These pins do not come in STL files but can be made out of short pieces of regular 1.75 PLA;- Hydraulic cables that connect the Droideka's parts are not provided with STL files. You can use 1.75mm filament of your choice and insert its pieces into designated holes;- The pistons on the Droideka's arms are retractable, i.e. they move when you bend the model's articulated arms;- For the highly articulated Droideka to stand firmly in any position you may choose there was a ratchet mechanism introduced in the model’s shoulder, sternum, and hip joints;- It is highly recommended that you watch "Assembly video" in the photo preview section and read "Assembly Manual" in PDF before assembling the Droideka;- All parts are divided in such a way that you will print them with the smallest number of support structures.DLP/SLA/SLS 1.0 version features:- Contains 20 parts;- A printed model in combat stance (P1) is 114 mm tall, 78 mm wide, 96 mm deep;- intermediate position (P2) is 101 mm tall, 86 mm wide, 109 mm deep;- wheel form (P3) is 74 mm tall, 68 mm wide, 71 mm deep;- Comprises parts for you to assemble Droideka in any of three static poses - combat stance, intermediate position, wheel form;- All parts are divided in such a way to fit the build plates and to ensure that support structures are generated where needed.FFF/FDM (Old version), DLP/SLA/SLS (Old version):- Comes in 1:10 scale;- Contain 47 and 48 parts respectively;- When printed both versions stand 177 mm tall, 121 mm wide, 149 mm deep;- The initial versions of the Droideka model that were uploaded in an incorrect scale;- These versions' features correspond with the ones of the FFF/FDM 1.0 version.WHAT WILL YOU GET AFTER PURCHASE?- STL files of Droideka Model for 3D printing which consist of 67 parts;- 2 versions of files for this model for FFF/FDM and DLP/SLA/SLS;- High-poly detailed model of Droideka​​​;- Assembly Manual for FFF/FDM 1.0 and DLP/SLA/SLS 1.0 versions in PDF format;- Detailed settings that we provide as a recommendation for Cura , Simplify3D and Slic3r for the best print;- Full technical support from the Gambody Support Team.You can get the model of Droideka for 3D Printing immediately after the purchase! Just click the green Buy button in the top-right corner of the model’s page. You can pay with PayPal or your credit card.Watch the tutorial on how to assemble Droideka​​​ 3D Printing Model at Gambody YouTube channel.Also, you may like other Space War Online 3D Printing Figurines as well as other Droid 3D Printing Models._______FAQ: Where can I print a model if I have no printer?How to get started with 3D printing?How to set up my 3D printer?How to choose right 3D model print bed positioning? How to paint printed figurine?This model was tested in Cura 3.4.1 and printed on an Ultimaker 2 in PLA material. Below you can find printing recommendations for Cura, Simplify3D and Slic3r softwares.To avoid printing problems, we recommend the following settings:QualityLayer Height: 0.1 mmInitial Layer Height: 0.3 mmLine Width: 0.4 mm Wall Line Width: 0.4 mm   Outer Wall Line Width: 0.4 mm   Inner Wall(s) Line Width: 0.4 mm Top/Bottom Line Width: 0.4 mm Infill Line Width: 0.4 mm Skirt/Brim Line Width: 0.4 mmSupport Line Width: 0.4 mm Initial Layer Line Width: 100%ShellWall Thickness: 0.8 mm    Wall Line Count: 2Outer Wall Wipe Distance: 0.2 mmTop Surface Skin Layers: 0Top/Bottom Thickness: 0.8 mm   Top Thickness: 0.8 mm      Top Layers: 8    Bottom Thickness: 0.8 mm      Bottom Layers: 8Top/Bottom Pattern: LinesBottom Pattern Initial Layer: LinesTop/Bottom Line Directions: [ ]Outer Wall Inset: 0 mmCompensate Wall Overlaps: Check    Compensate Outer Wall Overlaps: Check    Compensate Inner Wall Overlaps: CheckFill Gaps Between Walls: EverywhereFilter Out Tiny Gaps: CheckHorizontal Expansion: 0 mmInitial Layer Horizontal Expansion: 0 mmZ Seam Alignment: Sharpest CornerSeam Corner Preference: Hide SeamIgnore Small Z Gaps: CheckExtra Skin Wall Count: 1InfillInfill Density: 80%Infill Line Distance: 4.0 mmInfill Pattern: GridInfill Line Directions: [ ]Infill X Offset: 0 mmInfill Y Offset: 0 mmInfill Overlap Percentage: 10%    Infill Overlap: 0.04 mmSkin Overlap Percentage: 5%    Skin Overlap: 0.02 mmInfill Wipe Distance: 0.1 mmInfill Layer Thickness: 0.1 mmGradual Infill Steps: 1Gradual Infill Steps Height: 1.5 mmInfill Before Walls: CheckMinimum Infill Area: 0 mm2Skin Removal Width: 0.8 mm    Top Skin Removal Width: 0.8 mm    Bottom Skin Removal Width: 0.8 mmSkin Expand Distance: 0.8    Top Skin Expand Distance: 0.8    Bottom Skin Expand Distance: 0.8Maximum Skin Angle for Expansion: 90˚    Minimum Skin Width for Expansion: 0.0MaterialInitial Layer Flow: 100%Enable Retraction: CheckRetraction Extra Prime Amount: 0Retraction Minimum Travel: 0.8 mmMaximum Retraction Count: 90Minimum Extrusion Distance Window: 6.5 mmNozzle Switch Retraction Distance: 16 mmNozzle Switch Retraction Speed: 20 mm/s    Nozzle Switch Retract Speed: 20 mm/s    Nozzle Switch Prime Speed: 20 mm/sSpeed Print Speed: 45 mm/s    Infill Speed: 45 mm/s    Wall Speed: 22.5 mm/s      Outer Wall Speed: 22.5 mm/s      Inner Wall Speed: 45 mm/s    Top/Bottom Speed: 15 mm/sTravel Speed: 45 mm/sInitial Layer Speed: 22.5 mm/s  Initial Layer Print Speed: 22.5 mm/s  Initial Layer Travel Speed: 30 mm/sSkirt/Brim Speed: 30 mm/sMaximum Z Speed: 0 mm/sNumber of Slower Layers: 2Travel Combing Mode: AllAvoid Printed Parts when Traveling: CheckTravel Avoid Distance: 0.625 mmLayer Start X: 0.0 mmLayer Start Y: 0.0 mmCooling Enable Print Cooling: CheckFan Speed: 100%    Regular Fan Speed: 100%    Maximum Fan Speed: 100%Regular/Maximum Fan Speed Threshold: 10 sInitial Fan Speed: 0%Regular Fan Speed at Height: 0.3 mm    Regular Fan Speed at Layer: 2Minimum Layer Time: 5 sMinimum Speed: 10 mm/sSupport Generate Support: CheckSupport Placement: EverywhereSupport Overhang Angle: 50°Support Pattern: Zig ZagConnect Support ZigZags: CheckSupport Density: 15 %    Support Line Distance: 3 mmSupport Z Distance: 0.1 mm    Support Top Distance: 0.1 mm    Support Bottom Distance: 0.1 mmSupport X/Y Distance: 1 mmSupport Distance Priority: Z overrides X/YMinimum Support X/Y Distance: 0.25 mmSupport Stair Step Height: 0.3 mmSupport Stair Step Maximum Width: 5.0 mmSupport Join Distance: 2.0 mmSupport Horizontal Expansion: 0.2 mmSupport Infill Layer Thickness: 0.1 mmGradual Support Infill Steps: 0Use Towers: CheckTower Diameter: 3.0 mmMinimum Diameter: 3.0 mmTower Roof Angle: 65°Build Plate Adhesion Build Plate Adhesion Type: Brim (for all parts of locks use "Skirt")Skirt/Brim Minimum Length: 250 mmBrim Width: 8.0 mm    Brim Line Count: 18Brim Only on Outside: CheckMesh Fixes Union Overlapping Volumes: CheckMerged Meshes Overlap: 0.15 mmSpecial ModesPrint Sequence: All at OnceSurface Mode: NormalExperimentalSlicing Tolerance: MiddleMaximum Resolution: 0.01 mmFlow rate compensation max extrusion offset: 0 mmFlow rate compensation factor: 100%Disclaimer: This model will look outstanding if printed on SLA/SLS 3D printer. The accuracy of the model printed on FFF printer can vary from the result shown in the pictures.This model was tested with PLA material.To avoid printing problems, we recommend the following settings:ExtruderNozzle Diameter: 0.4 mmExtrusion Multiplier: 0.97Extrusion Width: AutoRetraction Distance: 5.00 mmExtra Restart Distance: 0.00 mmRetraction Vertical Lift: 0.08 mmRetraction Speed: 5400.0 mm/minWipe Distance: 5.00 mmLayerPrimary Layer Height: 0.2 mmTop Solid Layers: 8Bottom Solid Layers: 5Outline/Perimeter Shells: 2Outline Direction: Inside-OutFirst Layer Height: 90%First Layer Width: 100%First Layer Speed: 20%AdditionsUse Skirt/Brim: CheckSkirt Layers: 1Skirt Offset from Part: 6.00 mmSkirt Outlines: 5InfillInternal Fill Pattern: Fast HoneycombExternal Fill Patern: RectilinearInterior Fill Percentage: 80%Outline Overlap: 22%Infill Extrusion Width: 100%Minimum Infill Length: 5.00 mmCombine Infill Every: 1 layersExternal Infill Angle Offsets: 45/-45 degSupportGenerate Support Material: CheckSupport Infill Percentage: 15%Extra Inflation Distance: 1.00 mmSupport Base Layers: 0Combine Support Every: 1 layersDense Support Layers: 0Dense Infill Percentage: 70%Support Type: NormalSupport Pillar Resolution: 5.00 mmMax Overhang Angle: 60 degHorizontal Offset From Part: 0.50 mmUpper Vertical Separation Layers: 1Lower Vertical Separation Layers: 1Support Infill Angles: 45 degTemperatureExtruder 1 Temperature: 210Heated Bed: 60CoolingIncrease fan speed for layers below: 45.0 sec  Maximum Cooling fan speed: 50%Bridging fan speed override: 100%SpeedsDefault Printing Speed: 4800.0 mm/minOutline Underspeed: 50%Solid Infill Underspeed: 80%Support Structure Underspeed: 80%X/Y Axis Movement Speed: 10800.0 mm/minZ Axis Movemen Speed: 1002.0 mm/minAdjust printing speed for layers below: 15.0 sec   Allow speed reduction down to: 20%OtherUnsupported area threshold: 20.0 sq mLayer height  Layer height: 0.1 mm  First layer height: 90%Vertical shells  Perimeters: 2Horizontal shells  Soid layers:               Top: 8              Bottom: 5Quality  Detect thin walls: Check  Detect bridging perimeters: CheckAdvanced  Seam position: RandomInfill  Fill density: 80%  Fill pattern: Honeycomb  Top/bottom fill pattern: RectilinearReducing printing time  Combine infill every: 1 layersAdvanced  Solid infill every: 0 layers  Fill angle: 25 deg  Solid infill threshold area: 0mmSkirt  Loops: 2  Distance from object: 6 mm  Skirt height: 1 layers  Minimum extrusion length: 4 mmBrim   Brim width: 10 mmSupport material  Generate support material: Check  Overhang threshold: 45 deg  Enforce support for the first: 3 layersRaft  Raft layers: 0 layersOptions for support material and raft  Contact Z distance: 0.1 mm  Pattern: Rectilinear  Patter spacing: 2 mm  Pattern angle: 0 deg  Interface layers: 2 layers  Interface pattern spacing: 0.2 mmSpeed for print moves  Perimeters: 60 mm/s  Small perimeters: 20 mm/s  External perimeters: 20 mm/s  Infill: 60 mm/s  Solid infill: 60 mm/s  Top solid infill: 30 mm/s  Support material: 50 mm/s  Support material interface: 100%  Bridges: 30 mm/s  Gap fill: 50 mm/sSpeed for non-print moves  Travel: 60 mm/sModifiers  First layer speed: 30 mm/sAcceleration control  Perimeters: 800 mm/s  Infill: 1500 mm/s  Bridge: 1000 mm/s  First layer: 1000 mm/s  Default: 1000 mm/sAutospeed  Max print speed: 100 mm/s  Max volumetrix speed: 0 mm/sExtrusion width  Default extrusion width: 0.42 mm  First layer: 0.42 mm  Perimeters: 0.42 mm  External perimeters: 0.42 mm  Infill: 0.42 mm  Solid infill: 0.42 mm  Top solid infill: 0.42 mm  Support material: 0.42 mmOverlap  Infill/Perimeters overlap: 20%Flow  Bridge flow ratio: 0.95Other  XY Size Compensation: 0 mm  Threds: 8  Resolution: 0 mm