DEEJ volume control case

prusaprinters

<h3>Deej volume control case</h3> <p>Image album with with build photos and tips <a href="https://imgur.com/a/8WKr8W9">https://imgur.com/a/8WKr8W9</a><br/> For assembly instructions keep reading.</p> <h3>Project Github</h3> <p>Info regarding the Deej volume control project and arduino code can be found on the official <a href="https://github.com/omriharel/deej">GitHub page</a><br/> All I did was include some basic neopixel code in the provided arduino file from the GitHub,</p> <h3>Non-Printed parts used</h3> <p>5x 10k ohm linear potentiometers<br/> 5x Rubber knobs that fits 18-tooth 6mm shafts<br/> 8x12mm m3 screws (Optionally exchange 2 of them for longer screws)</p> <p>Links are to shops where I bought my parts -- it's just to help you identify what I used!</p> <p><a href="https://www.electrokit.com/produkt/arduino-nano-every-no-headers/">Arduino Nano</a> (Electrokit)<br/> <a href="https://www.electrokit.com/produkt/pot-10kohm-lin-p160kn-b10k/">Potentiometers</a> (Electrokit)<br/> <a href="https://www.electrokit.com/en/product/knob-rubber-yellow-o11-5x13-5mm/">Knobs</a> (Electrokit)<br/> <a href="https://www.aliexpress.com/item/32378187271.html?spm=a2g0o.cart.0.0.71353c00LXxpF4&amp;mp=1">Neopixel clones</a> (Aliexpress)</p> <h3>Assembly</h3> <p>1) Fit the wired electronics to the bottom of the lid piece. I used hot glue to keep the leds in place but the potentiometers are attached with a nut on the top.</p> <p>2) Place the the tray inside the main case and fit the lid with the electronics into the case. While holding it shut, turn it over and drop a nut into each of the four screw hole tunnels and then screw it shut. It helps to <a href="https://i.imgur.com/ftVGHmQ.jpg">hold the nut</a> in place while screwing it shut so the screw can catch the threads. I used two 19mm m3 screws for the longer diagonal channels but that's completely optional.</p> <p>3) Place four nuts into the hexagonal holes in the bottom piece. They can fall out easily so best thing is to use a small bit of glue to hold them in place, just don't get glue inside the threads! Then screw it shut.</p> <h3>Print instructions</h3><h3>Category: Electronics Summary</h3> <h3> Deej volume control case</h3> <p>Image album with with build photos and tips <a href="https://imgur.com/a/8WKr8W9">https://imgur.com/a/8WKr8W9</a><br/> For assembly instructions keep reading.</p> <h3>Project Github</h3> <p>Info regarding the Deej volume control project and arduino code can be found on the official <a href="https://github.com/omriharel/deej">GitHub page</a><br/> All I did was include some basic neopixel code in the provided arduino file from the GitHub,</p> <h3>Non-Printed parts used</h3> <p>5x 10k ohm linear potentiometers<br/> 5x Rubber knobs that fits 18-tooth 6mm shafts<br/> 8x12mm m3 screws (Optionally exchange 2 of them for longer screws)</p> <p>Links are to shops where I bought my parts -- it's just to help you identify what I used!</p> <p><a href="https://www.electrokit.com/produkt/arduino-nano-every-no-headers/">Arduino Nano</a> (Electrokit)<br/> <a href="https://www.electrokit.com/produkt/pot-10kohm-lin-p160kn-b10k/">Potentiometers</a> (Electrokit)<br/> <a href="https://www.electrokit.com/en/product/knob-rubber-yellow-o11-5x13-5mm/">Knobs</a> (Electrokit)<br/> <a href="https://www.aliexpress.com/item/32378187271.html?spm=a2g0o.cart.0.0.71353c00LXxpF4&amp;mp=1">Neopixel clones</a> (Aliexpress)</p> <h3>Assembly</h3> <p>1) Fit the wired electronics to the bottom of the lid piece. I used hot glue to keep the leds in place but the potentiometers are attached with a nut on the top.</p> <p>2) Place the the tray inside the main case and fit the lid with the electronics into the case. While holding it shut, turn it over and drop a nut into each of the four screw hole tunnels and then screw it shut. It helps to <a href="https://i.imgur.com/ftVGHmQ.jpg">hold the nut</a> in place while screwing it shut so the screw can catch the threads. I used two 19mm m3 screws for the longer diagonal channels but that's completely optional.</p> <p>3) Place four nuts into the hexagonal holes in the bottom piece. They can fall out easily so best thing is to use a small bit of glue to hold them in place, just don't get glue inside the threads! Then screw it shut.</p> <h3> Print Settings</h3> <p><strong>Printer Brand:</strong> Prusa</p> <p><strong>Printer:</strong> I3 MK3S</p> <p><strong>Rafts:</strong> No</p> <p><strong>Supports:</strong> No</p> <p><strong>Resolution:</strong> 0.15 - 0.22mm</p>