Da Vinci Webcam Mount

prusaprinters

<p>A shelf that attaches to the holes in the interior wall of a Da Vinci 1.0, 1.0A, and 2.0 printer, to mount a webcam (or other accessory).</p> <p>Specifically, I am using the TeckNet C016 USB HD 720P Webcam, 5 MegaPixel, 5G Lens, USB Microphone &amp; 6 LED (~$14, http://www.amazon.com/gp/product/B000Q3VECE ) because it has a close manual focus, and its own LED lights for when the Da Vinci's internal light turns itself off.</p> <h3> Specs:</h3> <p><strong>*Dimensions:</strong> 4.504"W x 1.250"D x 3.595"H (each)<br/> <strong>*Volume:</strong> 1.88 cubic inches<br/> <strong>*Weight:</strong> ~0.04 pounds</p> <h3> Files:</h3> <p><strong>*Shelf:</strong> PTW-00-1-PT-0195 (Mount, Camera, DaVinci).STL<br/> <strong>*Prototype Shelf:</strong> PTW-00-1-PT-0195 (Mount, Camera, DaVinci) Proto1.STL - Small shelf to mount the camera in the corner, inside the rails, but my camera was too big to fit.<br/> <strong>*Prototype Shelf:</strong> PTW-00-1-PT-0195 (Mount, Camera, DaVinci) Proto2.STL - Vertical shelf, but I didn't want to mount the camera sideways ultimately.</p> <h3> NOTES:</h3> <ul> <li>.STL names do not match .SLDPRT name because Da Vinci will not print file names over 56 characters.</li> </ul> <h3>Print instructions</h3><h3>Category: 3D Printer Accessories Summary</h3> <p>A shelf that attaches to the holes in the interior wall of a Da Vinci 1.0, 1.0A, and 2.0 printer, to mount a webcam (or other accessory).</p> <p>Specifically, I am using the TeckNet C016 USB HD 720P Webcam, 5 MegaPixel, 5G Lens, USB Microphone &amp; 6 LED (~$14, http://www.amazon.com/gp/product/B000Q3VECE ) because it has a close manual focus, and its own LED lights for when the Da Vinci's internal light turns itself off.</p> <h3> Specs:</h3> <p><strong>*Dimensions:</strong> 4.504"W x 1.250"D x 3.595"H (each)<br/> <strong>*Volume:</strong> 1.88 cubic inches<br/> <strong>*Weight:</strong> ~0.04 pounds</p> <h3> Files:</h3> <p><strong>*Shelf:</strong> PTW-00-1-PT-0195 (Mount, Camera, DaVinci).STL<br/> <strong>*Prototype Shelf:</strong> PTW-00-1-PT-0195 (Mount, Camera, DaVinci) Proto1.STL - Small shelf to mount the camera in the corner, inside the rails, but my camera was too big to fit.<br/> <strong>*Prototype Shelf:</strong> PTW-00-1-PT-0195 (Mount, Camera, DaVinci) Proto2.STL - Vertical shelf, but I didn't want to mount the camera sideways ultimately.</p> <h3> NOTES:</h3> <ul> <li><p>.STL names do not match .SLDPRT name because Da Vinci will not print file names over 56 characters.</p> <h3>Instructions</h3> <ol> <li>Print the shelf. Took ~2h:15m, and used 9.7m of filament. The settings I used are:<br/> A. Quality: Excellent<br/> B. Layer height: 0.20mm<br/> C. 3D density: High (50%)<br/> D. Supports: Yes </li> <li>Carefully remove the supports from under the hooks. This is the only place they should have been created. </li> <li>Test fit the shelf in your printer, in the front left corner, where the door opens. See picture for interior holes to use. </li> <li>Test installation of your webcam. </li> <li>Remove shelf, and secure webcam to the shelf with a cable tie, or other method. </li> <li>Reinstall shelf. Nothing should touch the metal rails, since they spin. </li> <li>Route wire, out door handle opening or side vent. </li> <li>Adjust webcam positioning and focus.</li> </ol> </li> </ul>