Case for Digispark Attiny85

prusaprinters

<p>This is a simple box for the Digispark AtTiny 85 device. Simple and easy.</p> <p>I have used the Attiny85 to create a small device that would prevent my computer from going into sleep mode when connected and running macros on remote computers.</p> <p>Just move the mouse a little every 20 seconds. In order to load the code, you need the arduino IDE and configure it as I show in the image.</p> <p>There is a remix from this design because this one doesn't work on some of my laptops (<a href="https://www.prusaprinters.org/es/prints/53317-case-for-attiny85-version-2">https://www.prusaprinters.org/es/prints/53317-case-for-attiny85-version-2</a>).</p> <p>The code is:</p> <hr/> <h3>include &lt;DigiMouse.h&gt;</h3> <h3>define led 1</h3> <h3>define move_interval 3</h3> <h3>define loop_interval 20 // en segundos</h3> <p>void setup() {<br/> DigiMouse.begin();<br/> randomSeed(analogRead(1));<br/> pinMode(led, OUTPUT);<br/> }</p> <p>void loop() {<br/> digitalWrite(led,HIGH);<br/> int distance = random(100, 800);<br/> int x = random(3) - 1;<br/> int y = random(3) - 1;<br/> for (int i = 0; i &lt; distance; i++) {<br/> DigiMouse.move(x, y, 0);<br/> DigiMouse.delay(move_interval);<br/> }</p> <p>for (int t = 0; t &lt; loop_interval; t++) {<br/> DigiMouse.delay(500);<br/> digitalWrite(led,LOW);<br/> DigiMouse.delay(500);<br/> }<br/> }</p> <hr/> <p>I recommend the PETg filament because it is a bit flexible and will help to get the device into the box.</p> <p>See images for help</p> <p>Print Recommendation:</p> <p>PETG filament<br/> layer height 0.2 mm<br/> nozzle 0.6 or 0.4 mm<br/> 15% - 20% filling<br/> without supports<br/> Orient the X on the bed</p> <h3>Print instructions</h3><h3>Category: Computer Summary</h3> <p>This is a simple box for the Digispark AtTiny 85 device. Simple and easy.<br/> I recommend the PETg filament because it is a bit flexible and will help to get the device into the box.</p> <p>See PDF for help</p> <p>Recommendation:</p> <p>PETG filament<br/> layer height 0.2 mm<br/> nozzle 0.6 or 0.4 mm<br/> 15% - 20% filling<br/> without supports<br/> Orient the X on the bed</p> <h3> Print Settings</h3> <p><strong>Printer Brand:</strong></p> <p>Prusa</p> <p><p class="detail-setting printer"><strong>Printer: </strong> <div><p>I3 MK3S</p>&lt;/div&gt;<strong>Rafts:</strong></div></p> <p>No</p> <p><p class="detail-setting supports"><strong>Supports: </strong> <div><p>No</p>&lt;/div&gt;<strong>Resolution:</strong></div></p> <p>0.2</p> <p><p class="detail-setting infill"><strong>Infill: </strong> <div><p>20%</p>&lt;/div&gt;<br/> <strong>Filament:</strong><br/> Prusament PETG Red <br/> <p class="detail-setting notes"><strong>Notes: </strong> </p><div><p>Care must be taken when inserting the device to avoid damaging any chip or component.<br/> See PDF for help</p></div></div></p></p></p></p>