
Build and have fun #2
prusaprinters
<p>Build and play</p> <h3>Print instructions</h3><table border="1"> <tr> <td colspan="2"> <b>Build for fun!</b> </td> </tr> <tr> <td colspan="2"> All the parts has been redesigned a bit. The holes is now cc 10mm. This means that you can position the cubes more flexible.</td></tr></table> The old system if not compatible in this matter. However for the cubes there are transition cubes which will fit the old and the new. I have noticed that wheels is a big deal. Therefor I've decided to build a raceway for the vehicles. I am also making a 60% raceway to fit common small cars. <tr> <td> <b>File</b> </td> <td> <b>Comment</b> </td> </tr> <tr> <td> Cube.stl </td> <td> A cube without any link </td> </tr> <tr> <td> CubeCenterPin.stl </td> <td> A cube with one center pin </td> </tr> <tr> <td> CubeCornerPins.stl </td> <td> A cube with 4-corner pins </td> </tr> <tr> <td> CubeMidPins.stl </td> <td> A cube with 4-middle pins </td> </tr> <tr> <td> CubeHalf.stl </td> <td> A cube, cut diagonal </td> </tr> <tr> <td> CubeTransition.stl </td> <td> A transition cube without any link, from the old system </td> </tr> <tr> <td> CubeTransitionCenterPin.stl </td> <td> A transition cube with one center pin, from the old system </td> </tr> <tr> <td> CubeTransitionCornerPins.stl </td> <td> A transition cube with 4-corner pins, from the old system </td> </tr> <tr> <td> CubeTransitionMidPins.stl </td> <td> A cube with 4-middle pins, from the old system </td> </tr> <tr> <td> Link.stl </td> <td> Short link </td> </tr> <tr> <td> LinkMedium.stl </td> <td> Medium sized link </td> </tr> <tr> <td> LinkMediumB.stl </td> <td> Medium sized link, both ends </td> </tr> <tr> <td> LinkMediumBLid.stl </td> <td> A "lid" for Link Medium B </td> </tr> <tr> <td> LinkLong.stl </td> <td> Long link </td> </tr> <tr> <td> LinkLongB.stl </td> <td> Long link, both ends </td> </tr> <tr> <td> LinkLongBLid.stl </td> <td> A "lid" for Link Long B </td> </tr> <tr> <td> M4_5 Bolt 14mm.stl </td> <td> Bolt 4.5mm, in sizes 14,24,34,44,54,64,74,84 mm </td> </tr> <tr> <td> M4_5 Nut Scale to 107.8.stl </td> <td> Nut to 4.5mm bolt, scale to 107.8% in slicer </td> </tr> <tr> <td> M8 Bolt 15mm.stl </td> <td> Bolt 8mm, in sizes 15,25,35,45,55,65,75,85 mm </td> </tr> <tr> <td> M8 Nut Scale to 106.stl </td> <td> Nut to 8mm bolt, scale to 106% in slicer </td> </tr> <tr> <td> Stick2.stl </td> <td> Stick, comes in 2,3,4,5,6,7,8 sections </td> </tr> <tr> <td> TowBlockWithLink.stl </td> <td> Tow block with link </td> </tr> <tr> <td> TowBlock.stl </td> <td> Tow block </td> </tr> <td> TowLink.stl </td> <td> Tow link for two TowBlocks </td> <td> BlockLink.stl </td> <td> A link to connect any cube etc... </td> <tr> <td> WheelBig50mm.stl </td> <td> Wheel for 8mm bolt or pin, suggested use with 30mm wheel </td> </tr> <tr> <td> WheelBig40mm.stl </td> <td> Wheel for 8mm bolt or pin, suggested use with 20mm wheel </td> </tr> <tr> <td> WheelBigPin.stl </td> <td> Pin to big wheels *2) </td> </tr> <tr> <td> WheelSmallPin.stl </td> <td> Pin to small wheels *2) </td> </tr> <tr> <td> WheelBalloon40.stl </td> <td> A sphere with holes, BALLOON Wheel </td> </tr> <tr> <td> WheelBalloon50.stl </td> <td> A sphere with holes, BALLOON Wheel </td> </tr> <tr> <td> Kryss.stl </td> <td> A cross, for e.g. a Helicopter </td> </tr> <tr> <td> Fast nyckel 13mm v1.stl </td> <td> A tool for the bolts and nuts of course :-) *1) </td> </tr> <tr> <td colspan="2"> <b>Notes</b> </td> </tr> <tr> <td colspan="2"> *1) For 7.5mm key (the M4.5), scale it to 57.7% in the slicer, that is for X, Y and Z </td> </tr> <tr> <td colspan="2"> *2) Can be very tight, but when on the wheel the wheel should spin free </td> </tr> <tr> <td colspan="2"> Compatible with<br/> https://www.prusaprinters.org/prints/40925-raspberry-pi-case-for-camera-with-flexible-stand </td> </tr> <tr> <td colspan="2"> <b>More Notes</b> </td> </tr> <tr> <td colspan="2"> I have experienced that different filaments have different properties. Sometimes the pins fits the holes, sometimes too tight and sometimes to loose. You have to try yourself. if it wont fit in one way it may fit in another. You may have to "exercise" the parts. Anyway, Have fun! </td> </tr> <tr> <td colspan="2"> Compatible raceway. Raceway one meter in diameter (24 pieces to print), with options such as driveway and hills 10% or 15% </td> </tr>
With this file you will be able to print Build and have fun #2 with your 3D printer. Click on the button and save the file on your computer to work, edit or customize your design. You can also find more 3D designs for printers on Build and have fun #2.