Buffed n Braced Einsy Door - Use with stock MK3s Einsy Base

prusaprinters

<p>This is a buffed/reinforced, braced Einsy door mod to brace the Z axis to the Y axis. Just use your stock Einsy base with this. This prevents the Z axis from wiggling and should improve your prints. I tried to keep this as simple as possible and instructions are below. It takes only a few hours to print. It works just as I intended and it really stiffens the wobble a lot! It is my favorite mod I have done because I consider it a requirement because it affects print quality, and not a just a nice to have.</p> <p>The door is modified to be stronger and thicker around the perimeter, the hinges are removed and it now attaches directly to the Z and Y frames, with the help of a small frame insert. You don't need to disconnect any cables from your Einsy case!</p> <p>You will need:</p> <ul> <li>two m3 12mm screws (m3 10mm will work ok)</li> <li><p>two m3 hex nuts Also check out my side mounted MK3 LCD mod<br/> <a href="https://www.thingiverse.com/thing:3483560">https://www.thingiverse.com/thing:3483560</a></p> <p>Now you can mount a Logitech or any camera with a screw mount securely to the front frame, as well as place you Pi there for Octolapse:<br/> <a href="https://www.thingiverse.com/thing:3518161">https://www.thingiverse.com/thing:3518161</a></p> <p>My cable clip keeps your LCD cables tidy:<br/> <a href="https://www.thingiverse.com/thing:3485143">https://www.thingiverse.com/thing:3485143</a></p> <p>My feet mod for reducing all vibration and noise by 95%, possible improving prints:<br/> <a href="https://www.thingiverse.com/thing:3496474">https://www.thingiverse.com/thing:3496474</a></p> <p>Fusion 360 File included for remixing.</p> <h3>Print Settings</h3> </li> </ul> <p><strong>Printer Brand:</strong></p> <p>MK3</p> <p><p class="detail-setting printer"><strong>Printer: </strong> <div><p>Prusa i3</p></div><strong>Rafts:</strong></p> <p>No</p> <p><p class="detail-setting supports"><strong>Supports: </strong> <div><p>No</p></div><strong>Resolution:</strong></p> <p>.2</p> <p><p class="detail-setting infill"><strong>Infill: </strong> <div><p>30% gyroid</p></div><br/> <strong>Filament:</strong><br/> [</p> <h3> Prusament PETG ](http://www.amazon.com/s?url=search-alias&amp;field-keywords=Prusament+PETG&amp;tag=thingiverse09-20) Orange <br/> <p class="detail-setting notes"><strong>Notes: </strong> </p><div><p>232/247 temp, no speed above 45, DoorBracket .2 layer height, FrameSlider .15 layer height</p></div> Custom Section</h3> <p><strong>Assembly Instructions</strong></p> <p><div><p>Before starting use the long press on the dial to raise the Z axis up and out of the way.</p> Prepare the FrameSlider part:</div></p> <ol> <li>Sand the FrameSlider part to ensure it will go in smoothly and can later be slide in the frame slot.</li> <li><p>Insert two m3 hex nuts and push them into the part firmly. Remove the stock Einsy Base and stock Einsy Door:</p> </li> <li><p>Slightly loosen the two m3 hidden screwsthat secure the Einsy Base to the frame so the it can be easily slide off.</p> </li> <li>Fully remove the long m3 bolt that attaches the base to the door. </li> <li>Slide off the Einsy base but keep the m3 frame bolts attached. Keep all the wires attached.</li> <li>Fully remove the Einsy door and hinges. You won't need the hinges anymore.</li> <li>Screw in the two door m3 10 screws from the Einsy door hinges back into the frame.</li> <li><p>Remove the single small square lock hex nut in the stock Einsy door door and place it aside for now. Remove the Rear Frame:</p> </li> <li><p>Remove the eight large screws on the rear 3030 metal frame: first loosen all the bolts very slightly, then once are all loose, fully remove them.</p> </li> <li>Gently lift it up the rear frame so you have enough room, and slide in the Frameslider part into the frame.</li> <li><p>Don't re-attach the frame screws just yet. Attach the new Door Brace:</p> </li> <li><p>Attach the DoorBracket to the Z axis frame first and screw in the two m3 10mm screws into the frame.</p> </li> <li>Then screw the bottom of the DoorBrace into the FrameSlider. You need two m3 12mm screws to attach it to the nut3030hex. I think m3 0mm might also work.</li> <li><p>Insert the small square hex nut into the DoorBracket slot for the long bolt to connect to later. Re-Attach the Rear Frame:</p> </li> <li><p>Put the rear frame back on and lightly screw in all 8 large screws.</p> </li> <li><p>Once they are all in tighten them. Re-attach the Einsy Base:</p> </li> <li><p>Place all the wires neatly in to the Einsy base.</p> </li> <li>Guide the X motor wire into the slot on the side of the base.</li> <li>Guide the base onto the bottom m3 10mm frame bolt, and gently shift it onto the top m3 frame bolt, while keeping all the wires inside.</li> <li>Screw the long bolt back into the Einsy base and tighten it. Make sure it pulls the hex nut we placed earlier into the door.</li> <li>Tighten the two frame bolts.</li> </ol> </p></p></p> Category: 3D Printer Parts