Artillery Sidewinder Hermes XYZ Linear Rail Mod++

thingiverse

You Need: for X-Linear Rail ----------------------------------------- 1x MGN12H 400mm Linear Rail 8x M3x8 cylinder-head-screw 8x M3 drop-in-t-nut for X-Endswitch ------------------------------------------- 1x M3x16 cylinder-head-screw for Hermes Mount ------------------------------------------ 1x Hermes Extruder 4x M3x10 countersunk-head-screw to mount on linear rail 3x M3x10 cylinder-head-screw to mount hermes extruder 1x M3x6 optional cylinder-head-screw to mount hermes extruder 2x M3x10 to mount plate holder 2x M3x6 to mount connector plate 2x M3x10 to mount end cap 2x M3x8 for BL-Touch (i think they are included with BL-Touch) for X-Rail electronic end cap------------------------------ 2x M3x10 for Z-Linear Rail ----------------------------------------- 2x MGN12H 550mm Linear Rail 20x M3 drop-in-t-nut (or less) 20x M3x8 cylinder-head-screw (or less) for Z-Linear Mount -------------------------------------- 8x M3x16 cylinder-head-screw 4x M5x25 cylinder-head-screw 4x M5 drop-in-t-nut 8x M3x10 cylinder-head-screw for Reverse Bowden ---------------------------------------- 1x M10 Ø4mm rod for reverse bowden holder 1x 14mm rod for spool holder 1x Filament Sensor Mount 1x USB and SD caps mounted from inside of the case 1x Reverse Bowden Holder mounted on the right side of the x-axis for Y-Linear Axis ---------------------------------------- 2x MGN12H 550mm Linear Rails to the two outer slot of the Y-Axis with 20x M3x8 cylinder-head-screw and 20x M3 drop-in-t-nut (or less) 6x M3x6 or M3x8 with some washers to mount the carriages 2x M5x10 or M5x16 cylinder-head-screw to two of the three holes for Y-Belt-Adapter Z-AXIS: 1. mount the two 550mm Linear Rails to the side of the printer with 20x M3 drop-in-t-nut and 20x M3x8 cylinder-head-screw (or less) 2. mount the lead screw nut to the linear lifter (8x M3x10 cylinder-head-screw) 3. screw the linear lifter to the linear rail carriage (8x M3x16 cylinder-head-screw) 4. mount X-Axis to linear lifter (4x M5x25 cylinder-head-screw and 4x M5 drop-in-t-nut) #Changes in Firmware define X_BED_SIZE 310 define Y_BED_SIZE 310 define X_MIN_POS 0 define Y_MIN_POS -6 define Z_MIN_POS 0 define X_MAX_POS X_BED_SIZE define Y_MAX_POS 315 define Z_MAX_POS 450 define NOZZLE_TO_PROBE_OFFSET { 0, 23, -2 } #Extra I also put in my spool holder thats mounted on the rear right side to 14mm rod (link below), a filament sensor mount, usb and sd caps mounted from inside of the case and an reverse bowden holder mounted on the right side of the x-axis. #My Mods: Electric: Hermera Extruder BTT-SKR V1.4 Turbo BTT-TFT3.5 V3 BL-Touch 1x dc12v/24v converter to 5v 5A for raspberry pi 1x raspberry pi 3b + camera with octoprint Mechanic: 2x fixed coupler for z-axis 4x Silicone Leveling Column 16mm 1x Aluminium bed 310x310 https://schmelz.bar/produkt/artillery-sidewinder-x1-upgrade-kits 1x Z-Axis Rods https://www.aliexpress.com/item/33023016436.html?spm=a2g0s.9042311.0.0.3d564c4dBUFGlZ #Next changes: better Y-Linear Axis Mod without drilling