another Leapfrog Creatr enclosure with Wifi Cam and side plates openers

thingiverse

Hi This is a Leapfrog Creatr enclosure with WiFi Cam and side plates openers. https://youtu.be/xDyH5j41lJM The walls are made of 5mm clear acrylic, with additional holes for flexibility. All screws, except rail screws, are M4 with M4 nuts and plastic washers (with a few lengthens and screw heads). Rail screws are M8 with their heads ground to fit in the rails. https://youtu.be/SmlmNkBJR4A Printed parts are made of ABS. There's a self-holding acrylic hinge, and upper hinges were printed in connected form but also included as two separate STL files. https://youtu.be/MmahfyKiX-0 A back holder for the enclosure is available, though I didn't use it. The acrylic part under the upper door serves two purposes: It provides a rest for the upper door, and closes the narrow gap between the upper door and the cover, preventing filament from getting stuck. https://youtu.be/Vwrk2PtWI3s Keep in mind that beneath this acrylic rest is a shorter corner (to offset for the 5mm part) inner -5mm .STL. The door handle is attached to the door with an iron screw and features a magnet holder that holds the door in place using a 6.2 mm x 6.2 mm diameter NEODYMIUM MAGNET. Side plates openers For maintenance and removing printed parts from the print bed, I use side plates openers from Ghost3D (http://www.thingiverse.com/thing:307931). They're very handy. https://youtu.be/QjYq-rN7A3s I've designed a slider lock that holds the acrylic enclosure on one end and serves as a slider to lock and unlock the side plates in place. WiFi Camera The WiFi camera used is the DX SKU 449864 (http://www.dx.com/p/suneyes-sp-v701w-720p-hd-mini-wireless-outdoor-ip-camera-eu-plug-449864#.WMU2rW996Uk). I replaced the M12 lens with a wider-angle lens, going from ~65 degrees to ~120 degrees. A new smaller enclosure based on Gilad's mount (http://www.thingiverse.com/thing:267313) was created, featuring a new holder and rail mount to hold the camera inside the printer and antenna outside. B.O.M LASER CUT (dxf files): 1 part of - quickest owl - leap - clear acrylic 5 mm one part 4.3.2017.DXF 1 part of - quickest owl - upper door - clear acrylic 5 mm one part 4.3.2017.DXF 1 part of - quickest owl - upper part - clear acrylic 5 mm one part 4.3.2017.DXF 1 part of - quickest owl - back part - clear acrylic 5 mm one part 4.3.2017.DXF 2 parts of - quickest owl - side wall - clear acrylic 5 mm two parts 4.3.2017.DXF 1 part of - quickest owl - front door - clear acrylic 5 mm one part 4.3.2017.DXF DOOR: 3 parts of - door hinge long.STL 3 parts of - boddy hinge.STL 1 part of - dore handel.STL 1 part of - boddy magnet holder therd view.STL UPPER ENCLOSURE: 2 parts of - corner.STL 1 part of - corner inner -5mm .STL 12 parts of - corner inner .STL 4 parts of - upper hinge assembly v 2 .STL ENCLOSURE AND PRINTER BRACKETS: 6 parts of - inner acrylic boddy holder.STL 4 parts of - outer boddy acrylic holder external wall holder.STL 4 parts of - outer wall holder slider.STL 2 parts of - outer boddy acrylic holder.STL 1 part of - inner boddy acrylic holder back v1.STL 1 part of - outer boddy acrylic holder back v1.STL WiFi Camera: 1 part of - boddy camera holder v2.STL 1 part of - CAMERA PT.STL 1 part of - camera cover.STL Camera back is from Gilad's files. Thanks, Amnon.