Alesis DM10 Module Mount Arm

thingiverse

This Mount arm lets you move the mount from the cross bar to the leg support.\r\nMy print came out fine and works great. If I needed to reprint again, I would change the module mount hole to 9.75 and sand it to fit. I did a test print with PLA, then used PETG for the actual print. I printed this laying down, with the hole opening up. Only minimal supports are needed where the shaft goes into the frame mount. Set random line changes otherwise you'll end up with a weak point.\r\n\r\nI suggest printing the test file first.\r\n\r\nModule mount hole #1 r=9.75\r\n Used in my file. > #2 r=9.8 \r\n #3 r=9.85\r\n\r\nStub for mount #1 10.75/10.75\r\n Used in my file. > #2 11/11 \r\n #3 11.25/11.25\r\n\r\nTest Print:\r\n\r\n // Mod Test Hole 1 : r=9.75\r\n difference() {\r\n translate([0,0,0]) cylinder (h = 5, r=13, $fn=100);\r\n // r= inside hole size\r\n translate([0,0,0]) cylinder (h = 26, r=9.75, center = true, $fn=100);}\r\n \r\n // Mod Test Hole 2 : r=9.80\r\n difference() {\r\n translate([30,0,0]) cylinder (h = 5, r=13, $fn=100);\r\n translate([30,0,0]) cylinder (h = 26, r=9.80, center = true, $fn=100);}\r\n \r\n // Mod Test Hole 3 : r=9.85\r\n difference() {\r\n translate([60,0,0]) cylinder (h = 5, r=13, $fn=100);\r\n translate([60,0,0]) cylinder (h = 26, r=9.85, center = true, $fn=100);}\r\n \r\n // Test shaft\r\n translate([0,30,0]) cylinder(5,10.75,10.75,$fn=100);\r\n translate([30,30,0]) cylinder(5,11,11,$fn=100);\r\n translate([60,30,0]) cylinder(5,11.25,11.25,$fn=100);\r\n\r\n\r\nMount Arm:\r\n\r\ndifference() {\r\n // Module Mount Hole.\r\n translate([0,0,227])rotate(a=[90,0,0]) cylinder (h = 25, r=14, center = true, $fn=100);\r\n // Module Mount Hole cut out. change hole size below r= and r= in the last line needs to be the same.\r\n translate([0,0,227]) rotate(a=[90,0,0]) cylinder (h = 25, r=9.8, center = true, $fn=100);}\r\n cylinder(45,11,11,$fn=100);\r\n // Mount Shaft 11,11 above and 11,12.5 below if a different size is needed. change only 11 numbers.\r\n translate([0,0,45]) cylinder(18,11,12.5,$fn=100); \r\n // shaft\r\ndifference() {\r\n translate([0,0,63]) cylinder(162,12.5,12.5,$fn=100); \r\n translate([0,0,227]) #rotate ([90,0,0]) cylinder (h = 26, r=9.8, center = true, $fn=100);}\r\n \r\n\r\n\r\n\r\n\r\nIf you print one of my files and have issues, or if you want something tweaked or have ideas on how to make it better, I'd love your feedback - good or bad.