Air Fitting Hanger, Magnetic

prusaprinters

<p>This little magnetic hook lets you hang your extra air compressor fittings right on the side of the tank.</p> <h3> Specs:</h3> <p><strong>*Dimensions:</strong> 2.000"W x 1.375"D x 1.125"H<br/> <strong>*Volume:</strong> 0.68 cubic inches<br/> <strong>*Weight:</strong> ~0.03 pounds</p> <h3> Files:</h3> <p><strong>*Hook for 18.5" diameter tanks:</strong> PTW-00-1-PT-0227 (Hanger, Air Fitting, Type D, 18.5in).STL<br/> <strong>*Hook for 20" diameter tanks:</strong> PTW-00-1-PT-0227 (Hanger, Air Fitting, Type D, 20in).STL</p> <h3> Needed to complete assembly:</h3> <ul> <li>QTY 3-6: 10mm diameter x 2.6mm thick Neodymium Magnets - <a href="http://www.dx.com/p/10-x-3mm-ndfeb-neodymium-magnet-circular-cylinder-diy-puzzle-set-silver-50-pcs-229283#.VOqSt9jnQYI">http://www.dx.com/p/10-x-3mm-ndfeb-neodymium-magnet-circular-cylinder-diy-puzzle-set-silver-50-pcs-229283#.VOqSt9jnQYI</a> (Description says 3mm thick, but are actually 2.6mm) </li> <li>Epoxy: For gluing in magnets </li> <li>(OPTIONAL) Plasti-Dip spray: Spray on magnets, to give them some friction.<br/> NOTES:</li> </ul> <hr/> <ul> <li>.STL names do not match .SLDPRT name because Da Vinci will not print file names over 56 characters. </li> <li>.STL files oriented for printing. </li> <li>Supports are needed to print the part.</li> </ul> <h3>Print instructions</h3><h3>Category: Tool Holders &amp; Boxes Summary</h3> <p>This little magnetic hook lets you hang your extra air compressor fittings right on the side of the tank.</p> <h3> Specs:</h3> <p><strong>*Dimensions:</strong> 2.000"W x 1.375"D x 1.125"H<br/> <strong>*Volume:</strong> 0.68 cubic inches<br/> <strong>*Weight:</strong> ~0.03 pounds</p> <h3> Files:</h3> <p><strong>*Hook for 18.5" diameter tanks:</strong> PTW-00-1-PT-0227 (Hanger, Air Fitting, Type D, 18.5in).STL<br/> <strong>*Hook for 20" diameter tanks:</strong> PTW-00-1-PT-0227 (Hanger, Air Fitting, Type D, 20in).STL</p> <h3> Needed to complete assembly:</h3> <ul> <li>QTY 3-6: 10mm diameter x 2.6mm thick Neodymium Magnets - <a href="http://www.dx.com/p/10-x-3mm-ndfeb-neodymium-magnet-circular-cylinder-diy-puzzle-set-silver-50-pcs-229283#.VOqSt9jnQYI">http://www.dx.com/p/10-x-3mm-ndfeb-neodymium-magnet-circular-cylinder-diy-puzzle-set-silver-50-pcs-229283#.VOqSt9jnQYI</a> (Description says 3mm thick, but are actually 2.6mm) </li> <li>Epoxy: For gluing in magnets </li> <li>(OPTIONAL) Plasti-Dip spray: Spray on magnets, to give them some friction.<br/> NOTES:</li> </ul> <hr/> <ul> <li>.STL names do not match .SLDPRT name because Da Vinci will not print file names over 56 characters. </li> <li>.STL files oriented for printing. </li> <li><p>Supports are needed to print the part.</p> <h3>Instructions</h3> <ol> <li>Print the part, with supports under the hook, and in the magnet pockets. Print at 100% fill, for strength. </li> <li>Epoxy in magnets. I found it best to put a plastic shopping bag over each magnet, as I epoxied it, and hold them in place until it sets, to keep them from magnetically jumping to each other. It's easier to have a friend help with this. </li> <li>(OPTIONAL) Spray a couple coats of Plasti-Dip rubber spray over the magnets, to give them some grip on the air compressor tank.</li> </ol> </li> </ul>