zwo 1600mm pro 3d models

This adapter connects a ZWO PE200 pier extension for ZWO AM5 mount to an iOptron pier, either the iOptron Permanent Pier or the iOptron Tri-Pier. The ZWO PE200 was designed to be able to be attached to both SkyWatcher and iOptron tripods. For...

Cameras like ZWO ASI120MM or ASI120MC cannot reach focus in Coronado PST telescope. It is possible however to obtain focus with a 2X barlow lens, but then the whole image of Sun doesn't fit into one frame. Reaching focus without 2x barlow lens...

Adapter for mounting a ZWO EAF to a Meade LX85 6" Newtonian. You will need to take the focuser apart and drill two 3mm holes in the retaining plate on center. Two 20mm M3 socket head screws are installed through the sheet metal and held in place by a...

This is a drop-in replacement for the ZWO 11mm T2 ring (M42*0.75 female-to-female thread). It allows correcting tilt in the imaging train. Use 5mm to 12mm M3 bolts and nuts. ... Print with PETG, 0.2mm or 0.15 layer, 15% gyroid infill.

The ZWO EAF Holder is specifically designed for use with Celestron Edge HD 8, 9.25 and RASA 8 telescopes or other similar models from Celestron's SC line. To fit the drive shaft, you'll need to carefully trim the end of the handle cap. ...This clever...

This design is a bracket to adapt a ZWO ASI EAF to the Explore Scientific Comet Hunter Crayford focuser. This bracket clamps around the base of the Comet Hunter Crayford and provides a shelf for the EAF to mount to. ... Filament: 1.75 PETG 100%...

It is remixed from jamesdedij's excellent ZWO filter holder. Printable in two parts, 2pcs. M5*30 screws are needed to join the parts. I also added some epoxy. The camera is mounted by it's 1/4-20 UNC photography thread. There is a degree-scale...

This is a mount for the ZWO ASIAIR, ZWO EAF, and guide scope to the Redcat 51. It uses a printed bracket and gear. You will also need: SmallRig Seamless Focus Gear Ring (72mm to 74mm) - 3293 for the printed gear to move the helical focuser.

This 36MM Filter Holder is sized to size the Chroma 36MM unmounted filters and the ZWO 36MM Filter Wheel. It is made to encase the portion of the filter that is visible above the height of the filter wheel filter indentation. I would recommend...

I was made a ring camera holder, for people hoy used hes canon lenses or other, inspider in a ZWO camera ring fit all cameras with 78mm diameter lock dovetail https://www.aliexpress.com/item/1005003250476143.html Dovetail:...

I didn't want to attach my ZWO EAF to my C9.25 permanently, as this makes it harder to transport and cumbersome to use visually. I designed the holder in a way that only a small base part is attached permanently and does not hinder using the...

ETOASI is an adapter designed to link Sony E-mount lenses directly to ASI cameras by ZWO Optical. To assemble it fully, you'll need three M4 knurled screws. Moreover, you must create three M4 threads within the predetermined holes using a hand tool...

NOTE = THIS PROJECT IS ONLY SUITABLE FOR A SKYMAX 127 AND ZWO EAF WHERE THE DOVETAIL BAR IS ON THE SAME SIDE AS THE FOCUSING KNOBFeatures:A simple to attach adapter which extends the dovetail bar providing a platform to fit the zwo EAF in two...

This basically replaces the included metal bracket with the ZWO EAF. The Focuser coupling should be press-fit (it is keyed) - but also includes holes for threading the grub screws in. For attaching the vertical part of the bracket, I did a...

This is just another way of fixation for ZWO EAF to William Optics 51 series telescopes. I wanted to keep the center of gravity as low as possible. I printed it with my Dremel 3D20, it fits perfectly. It is design for 280mm long GT2 belt, 6mm...

GSO 2" M-LRN 10:1 Linear Bearing Crayford Focuser, normally found on GSO Imaging Newtonian Reflector OTA, has a curved, concave, surface and different spacing incompatible with the included ZWO EAF aluminum bracket. This sturdy ABS-printed...

This 3D-printed component securely fastens onto the M4 threaded holes on the back of the ZWO ASI120 camera and firmly bolts into the 1/4"-20 tripod socket on the base of the Canon DSLR. ...Specifically designed for the EOS 650D, slight adjustments are...

This basically replaces the included metal bracket with the ZWO EAF. The Focuser coupling should be press-fit (it is keyed) - but also includes holes for threading the grub screws in. For attaching the vertical part of the bracket, I did a test-fit...

... it could damage you focuser if it is too long. The backlash of this set is about 50 steps of EAF and the total length of the draw tube is about 40000 steps. https://www.printables.com/model/333592-focusing-set-for-takahashi-toa-130ns-zwo-eaf

- - - Si tratta di un fuocheggiatore elicoidale per guida fuori asse della ZWO da usarsi con ASI120mini o con altre mini di analoghe dimensioni (diametro). Non so se funzionerà anche su altre guide fuori asse ma di sicuro questo mio progetto è...

ZWO EAF Holder for Celestron Edge HD 9.25 or other similar Celestron SC telescopes features a quick unlock mechanism for manual focusing. ### BOM * 1x GT2 Timing pulley with 20 teeth and a bore of 5mm * 1x GT2-142mm Timing Belt with a size of 6mm *...

This adapter converts a ZWO ASI Camera (or other CCDs with a C Mount) using a DSLR lens (here a Nikon lens) to use with telescope mounts. It also carries a finder dovetail shoe. There are two versions of the actual holder: One is a two-part and...

This is a remix of the ZWO EAF Holder for Celestron Nexstar 6/8/9 by jamesdedij (February 29, 2020) for the Celstron SCTs and I thank him for sharing the editable design files with me. I have modified all of the parts in Fusion 360 to fit the...

I'm not sure why I downloaded three motor mounts and none of them fit my motor holes perfectly. So, I decided to create a custom version for the HobbyKing FPV plane called Go Discover. The motor in question is the purple one visible in the pictures.

Given Stl are for my specific plug. ... Launch customizer for yours!

Adjusted to fit the Asiair Mini.

Customized version of https://www.thingiverse.com/thing:4581618 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4581618

Designed up this filter filter drawer holder because I was worried about dropping a filter drawer while changing them. Printing: My best prints were 80% in-fill, I used PETG filament 240C nozzle and 60C bed. ...

Cord bracket that mounts in place of the Finder Shoe on the side of the RA head.

Build exactly as shown in this video: https://www.youtube.com/watch?v=U7CCWhEAuhc.