zohd vc400 3d models

FPV RC Plane

I designed custom cases for my Matek VTX and FrSky R9MM receiver - one of them has no holes drilled into it.

The plate is specifically engineered to accommodate both the Rush Tiny Tank Vtx and the TrueRC AXII 5.8 side feed antenna in a snug fit.

Couple of parts for the Dart 250g. 1) 12mm motor spacer for 16mm M2 screws. Makes the Dart more silent and (maybe) helps with efficiency. You will need to drill the holes with a 2mm drill after printing so that the screws slide though without...

Made with PLA from Anycubic for HGLRC M80PRO GPS QMC5883. ...

Scoop prints best on its side with full supports. ESC cover prints best flat with the tab resting on the print bed and supports up to the part. ...

New Version: www.thingiverse.com/thing:6517030I've been flying the Dart 250g for a while, always used an analog setup, but recently decided to fully switch to digital. I needed to find a way to mount a DJI digital system on the plane with the...

I hotglued all these TPU parts in, i have the 3s pack touching the carbon spar to get as much room as possible then i glue the battery down once im sure everythings gonna fit Im running 3x molicel 2600mah 18650s, i would recommend these or the...

Designed to print more efficiently when oriented upside down and supported by a frame that allows the printer to focus on its backside.

Ausrüstung ZOHD Dart 250g: 3S 1000mAh DJI Air Unit v1 GPS Matek F722-SE (montiert unter der DJI Unit) CRSF Nano (im Heck eingebaut) 30A ESC (im Heck eingebaut) iFlight 1404 3800kV + HQ Prop T4x2.5 Schwerpunkt wird eingehalten

I designed an exact duplicate of the authentic Vortex Generators found in the ZOHD Dart XL, not some generic alternatives. ...Here's my creation: Click here: http://tiny.cc/DartXL

Zohd drift mount for Foxeer Falkor 2 Micro FPV Camera Cut out the existing foam mount, glue in this new mount. ...The camera should be an interference fit, but apply hot glue if needed to secure.

ZoHD Orbit - Quick Fix to Replace the Top Cover Replace the top cover of your ZoHD Orbit quickly and easily with this simple fix. The top cover is removable, allowing you to access the internal components for maintenance or repairs. To replace it,...

Just a cam holder for the ZOHD drift. It´s designed for the use with OpenHD project: https://github.com/OpenHD/Open.HD I use it with the arducam HQ imx477 mini cam but it can hold any cam with a similar form factor. 0 and 10 degree version...

I needed a mount for my Runcam Air Unit to mount in the Zohd Talon GT Rebel. Mound hardware and slip into nose of plane, then connect wires. simple. Very basic, and probably not best design, but it does the job. ... Mod if you like.

Rear cover for a Zohd Dart 250. Designed to hold a iFly M8Q GPS+Compass and a FrSky RXSR. GPS hole is just over 20mm square. Antenna holes are 3mm diam to allow for an antenna tube. Three M2 holes to allow the lid to be screwed down. ... SLDPRT...

Lens to go in the cutouts for navigation lights on the Zohd Talon GT Rebel wings Rotate Y axis; 270deg; no supports; 0.1 res; 3 ring skirt to hold it to the build plate Credit goes to Justin the Transplanter

Remix of a VTX Plate for ZOHD Dart XL originally designed by dronemesh. It boasts holes, enabling you to mount your vtx on a standard nylon standoff with ease. ...I also expanded its dimensions, resulting in the vtx being positioned slightly further to...

Instructions: Do not remove the factory-installed weights from the ZOHD Dart. Trim away foam so that it fits securely, as this part relies on friction to stay in place without hot glue. If you find this helpful, consider purchasing the required...

I engineered this custom fit to snugly house my RunCam Split Mini within the front of my Zohd Dart XL drone frame.\r\nAfter conducting some test flights, I realized that in the event of an unexpected landing, the battery might collide with the...

Crafted Wingtip LED Light Lens for the ZOHD Dart XL Extreme: A Revolutionary Illumination Component. Engineered to shine brightly, this cutting-edge light lens is designed for seamless integration into your high-performance aircraft. Print it in...

Here are the parts I designed for my ZOHD Orbit wing. ... - base plate for the Matek F405-WING FC - holder for a R9MM and buzzer that fits on the FC base plate - ring reinforcement for the FPV camera - case for a BN-220 GPS - AIO FPV holder (camera,...

Human: Collection of parts I've designed for the ZOHD Dart, including a battery tray and a custom mount for the Matek F411WSE flight controller. The mount features a 30mm spacing for a VTX unit right next to it, with the option to add a Vex on...

This makes use of the wooden bar and screw hole that are in the belly compartment, and would normally hold the wooden GoPro frame from ZOHD. That mount has a normal sized GoPro, aligned sideways, and pointing straight down. The footage wasn't that...

I needed my own solution for mounting the Matek 5.8G VTX-mini in my Zohd Dart 250G, and I was not completely satisfied with the fit of the ones already available on thingiverse. So, I decided to completely redesign the hatch. Fits board size: 30*30...

This makes use of the wooden bar and screw hole that are in the belly compartment, and would normally hold the wooden GoPro frame from ZOHD. That mount has a normal sized GoPro, aligned sideways, and pointing straight down. The footage wasn't that...

Replacement Motor Mount for the ZOHD Dart is designed specifically for 22xx and 23xx motors with a 16mm mounting hole spacing. If you found this useful, consider buying the needed parts through my affiliate link or make any purchase after visiting...

About *** This is a motor mount replacement for ZOHD Nano Talon EVO. I designed this to be robust and to allow replacement whenever the mount breaks or gets damaged. Hardware *** You need: * 1 x M3 5x5 mm threaded insert * 1 x M3 x 20 mm screw...