zohd vc400 3d models

Before flying my ZOHD Dart 250g I thought about the possible damage that can be caused when landing. I designed this piece to avoid such damage on landings. For this I made two "skates" with which to slide without affecting aerodynamics. ... Also,...

VTOL conversion kit for the ZOHD Talon GT Rebel airplane Needed parts: 2x servos, Dualsky AS82MG Servos will fit properly 2mm self tapping screws 2x 8x12x3.5mm ball bearings Motors used: IFlight XING-E 2207 1800KV in the back 2x EMAX Eco-II 2807...

... Micro. ... May work with other, similar cameras. Adds just enough size to fit snug in the right side camera bay of the ZOHD Dart XL Extreme. I added a piece of foam tape to the top for better grip. ... Using two sided tape would really lock it in.

A couple extras for the ZOHD Drift including a board holder for the Matek F411 WSE controller that fits the whole pattern of the Drift bay. Also added an LED holder for a 4x WS2812 LED board and a servo holder for a 3.2gr digital servo. ... I...

ZOHD Dart 250g Nano Camera Mount Fits 14mm nano camera into the nose area. No fixing required as it's a friction fit and in the event of a crash has a greater chance of survival. ... Printing: Printed in PLA with 20% infill, no supports but...

Simple nano camera (14*14 mm) mount like Caddx Ant Nano or Foxeer Razer Nano to fit into ZOHD Dart 250g. You can simply change camera view angle at any time. ... Links to cameras: Caddx Ant - https://www.banggood.com/custlink/vKmRWTfseM Foxxer...

A simple swap-out battery bay plate for the ZOHD Dart XL is what I needed, but alas, one wasn't readily available. Not being an engineer by trade, I had to roll up my sleeves and get creative, making a few adjustments along the way to suit my needs.

Foxeer Predator Mini camera mount for ZOHD Dart 250G This camera supports OSD with battery indicator, so fits basic FPV kit perfectly. In order to move connectors down it's possible flip image using camera controls. Camera shoul be moved far back...

Redesigned ZOHD Dart motor mount for 220x (2206/2207) brushless motors. Mount it anywhere with four fixing holes, saving motor cables during landing. Even mount the support sideways to keep those cables clear. This redesigned mount fits snugly into...

Attempting to boost airflow in the ZOHD orbit. Currently, there's one small NACA duct at the top of the wing and a minuscule exit at that end of the wing. This modification will replace the lower panel of the wing, allowing more air to flow across...

Replacement low profile back hatch for ZOHD Dart XL Beds smaller then ( 235mm x 235mm) use the 2 piece hatch, but with carefull placement the full size 1 piece hatch will fit diagonally. ... I advise to print a single skirt with 1mm offset from print...

Replacement nose hatch for the ZOHD Nano Talon EVO. Printed using eSun PLA-LW on an Ender 3 with direct drive extrusion. The included gcode file will work with any Ender 3 with a 0.4 mm nozzle. Use CA glue to attach the thumb screw. This...

You can install some LED lights on the back of your ZOHD Dart, near the motor, to create a unique lighting effect. It's a good idea to use a strong adhesive like glue to secure them in place. ...The specific LEDs I'm referring to are available here:...

Used in combination with ZOHD 1406 2600kv motors. Please note, there's a left and a right version (similar but 5 degree angle difference).Make sure to print it on it's side and use some support. After printing make sure to sand the front side flush...

Replacement motor mount for the ZOHD Dart XL is now available, featuring a redesigned structure that provides added strength and durability within the fuselage. This new design addresses the previous vulnerability of the original mount, which often...

Hello everyone! This is the ESC cover with magnet retention for the ZOHD Dart 250g. The antenna hole can be made or not, depending on your specific need. Support my model by clicking this link: https://www.buymeacoffee.com/Carletto73 Your support is...

This is a reinforced firewall for the ZoHD Dart XL Extreme, boasting a trust angle correction already seamlessly integrated. To install it, simply remove the original firewall and make some precision holes on the position of the "spikes" using a...

I found this https://www.thingiverse.com/thing:3605567 and wanted to use it, but it flopped around so I made this little bar to attach to my GT2 talon (Zohd). Still have to fine tune where the two design meet. busy printing now. IT fits on the...

This is a mount for the ZOHD Talon Rebel GT. Will likely require some enlargement of the hole for the SMA and attaches to the sidewall of the front compartment of the plane. Fastens to the plane with two small zipties to hold it in place. Mostly...

Replacement Low Profile Back Hatch for ZOHD Dart XL. When it comes to beds smaller than 235mm x 235mm, consider using the two-piece hatch. However, with precise placement, you can also fit the full-size one-piece hatch diagonally. For optimal...

Upgrade Kit for VTX, Matek GPS, SMA Mount for Antenna Zohd Dart XL - Upgrade to the Future: http://bit.ly/2EbdXaT Matek F405 Wing - Unleash the Power: http://bit.ly/2DJCpz8 AKK Infinite - Endless Possibilities: http://bit.ly/2rTCJEd Runcam Eagle 2...

This piece secures the servo-connector to the wing on the ZOHD Dart RC plane. It's a challenging print due to its tiny dimensions and the requirement for a precise fit with the connector. The final outcome is heavily influenced by the printer and...

This custom piece slides into the rear of the front pod on the ZOHD Orbit wing, providing a secure spot to zip-tie the VYX. The stand-offs molded into the side ensure optimal cooling performance while in use. A 6mm hole is also conveniently located,...

This is a Zohd Dart 250gr mod to space the motor towards the rear of the model and correct the angle of attack by 3 ° upwards. It increases efficiency and corrects the incidence of the motor which on this model is too oriented downwards. Its...

... securely fastened to prevent any movement or vibration that could affect their performance. That's it! With these custom covers installed, your ZOHD Talon Rebel GT drone will be ready for its next adventure with a sleek and professional look.

This is my GPS mount ( Beitian BN-220 ) for the ZOHD Dart250 wing. I didnt like the GPS position that this wing plane provide, that should be behind the air inlet from the inner part, so i decided to put it in the cockpit area , but not stuck to the...

I made those objects to upgrade my ZOHD Nano Talon with a iNav powered flight controller. There are three objects: FC mount which fits the Omnibus F4 Top plate for the TBS Unify antenna Bottom plate for the TBS Unify Print Settings Printer Brand:...

I aimed to assemble a ZOHD Dart 2s setup with a high Kv motor configuration similar to the Strix Nano Goblin. The 12x12mm motor mounting commonly found on 1407 and comparable sized motors won't fit the Dart's standard mount, however. So I designed...

This latch is designed to swap out magnetic catches on the battery bay of the ZOHD Dart XL. Why did I make it? I'd installed an Eagletree MicroVector in mine and the GPS and compass unit needed a spot that was far enough away from those magnets to...

This is for a ZOHD Alphastrike. I wanted a HD cam on this plane, but I didn't want to ruin the aerodynamics. It drives me nuts when people take a nice looking airframe and mount a camera to the top like an airbrake. Anyways, after quite a few...