zohd vc400 3d models

Not for print, This is a scan to use as reference if you want to create any custom parts for the dart 250 Unfortunately the underside scan corrupted, but if there is enough interest in this I'll look at doin another scan including some separate...

After my quad was taken down by a pilot, I needed new elevons. I didn't want to pay $50 for spare wing parts. I designed and created these elevons with the same shape as the originals, but they are made to be fitted slightly differently. They attach...

Remix with smoothed edges and rounded corners to fit in a Ender-3 220x220 build area. Do note that its a tiny bit shorter then the original wooden tray, if demanded i could release a slightly longer one. ...Thanks to hi_im_jonn0 for releasing the...

Includes:Rear Hatch with a slot for the TBS Unify Pro32 HV and an MMCX 90 degree Antenna, such as the Foxeer Lollipop20x20 M3 glue- (or velcro-)on stack mount (I use a Matek H743-mini V3)14mm camera canopy (tested with the Caddx Ant)The rear hatch is...

I specifically designed a custom cover for my Dart250g, which provides a snug fit for both the Runcam Phoenix and the Runcam Split Mini 2 cameras, placing them side by side in the nose of the Dart. ... Printed with PETG, I made sure to keep an eye on...

Are you looking to shave those last grams off your model, aiming for that 250g legal limit? This drop-in motor mount replacement might be just what you need. Made from PETG, it weighs in at an impressive 1.56g - a whopping 1.80g less than the carbon...

Print it on ABS or tpu because peanut gets hot as hell! i did helped you? So buy me a bear! ...my PayPal mail is contato@ipamp.com.br

I'm extremely impressed with this model, regardless of whether hi_im_jonn0 or Xermalk created it initially. ...After taking a closer look, I decided to extend the design to fill the side grooves all the way from the nose to the tail, which should make...

Note: This is untested with the original motor mount, but works seamlessly with this one https://www.thingiverse.com/thing:3816447. I aimed to craft a sleek low-profile Canopy, drawn inspiration from several impressive designs by other creators, yet...

Canopy to replace the foam one. The support underneath will also prevent a 18650 Li-On 2s battery from coming forwards and changing the COG during flight. Vent up top to cool VTX. Aerial MMCX connector to point towards front of aircraft when mounting...

I smashed mine during a flight and needed to print a replacement quickly, so I uploaded it for others to save them some time. This model is designed to fit snugly into the foam, but you should still use glue for extra security. There are two...

About *** This is a GoPro Bones mount for Nano Talon. The mount moves the GoPro farther away to the back to avoid air drag as much as possible. Also, it uses an M3 screw to secure the GoPro, instead of an M5 screw, to reduce weight. Total weight of...

I've Improved the Grill, Enhanced Dimensions, and Adjusted VTX Exit Position for Better Performance. Next Version: Expect Exciting Updates! Changes (v3.5): 1. Increased Thickness to a Sturdy 2mm 2. Refined Edges on VTX Hole and Support for Smooth...

Hi everyone! For those rocking a nano talon and a receiver with flexible antennas, this design is specifically tailored just for you. I was in need of a mount for my receiver that would keep the antennas at a 90-degree angle from each other while...

After crashing my plane the nose completely broke off. The battery bay walls were a little too easy to move so I (very quickly) designed this brace. Helps keep the plane a bit more rigid. ... You may need to shorten by a very small amount for less of a...

Print in TPU upside down. No supports needed. It's designed so that you should stick a piece of double sided foam tape under it (like the disk that comes with it). Just slap that onto the bottom of the gps and then press it into the mount. Cut the...

Mount your VTx antenna on front canopy and get your underneath VTx ventilated.

https://youtu.be/HYuKcdfvuBU Micro hd camera mount. Allowing air to flow and give more down angle pov for fpv. Friction fit. Glue if you would like. ... V2 is better.

I fitted an FPV camera at the front of my plane and created a small air-intake to cool off the camera and the camera board (runcam split 2). I highly recommend this intake if you have your camera mounted on the small black plastic support, as it will...

This is a simple mount for TBS Crossfire Nona (Micro) RX antenna. It's very easy to install and maintain. ...I used heat shrink tube with nylon tie and antenna inside it.

This part is to replace the original auto pilots wooden plate with a plate that holds the matek F7 wing underneath as well as the GPS stand to raise the GPS antenna.

I wanted a clean way to mount the VTX and Antenna on my Nano Talon Evo. These parts mount to the underside of the nose/canopy lid and are out of the way of the battery etc. You'll need to cut a 17mm hole in the lid for the antenna mount. The...

<p>I wanted a clean way to mount the VTX and Antenna on my Nano Talon Evo. These parts mount to the underside of the nose/canopy lid and are out of the way of the battery etc. You'll need to cut a 17mm hole in the lid for the antenna mount. The...

Wing servo plug covers to provide a neat finish and give a little more aero. ... See video for more details https://youtu.be/36a_YmIp3Zk

A mounting plate for TBS Crossfire Nano receiver and cover with airflow https://youtu.be/36a_YmIp3Zk

<p>The parts were printed with PETg and the sideplates were fixed with double sided tape to the fuselage.</p><p>The antennas lays flat against the foam of the fuselage and they are not able move in flight.</p><p>The hatch closes without cutting any...

Stack adapter for the Kopilot Lite board. ... Use this adapter to replace the bottom tray of the Kopilot Lite so you can stack it onto the FPV Combat board and save space in your build.

The Dart 250g canape carbon thing goes into the holder and is secured by a small screw. ... - CG is just slightly shifted to the front considering the weight of the runcam 2 (4k) - Easy to print (Print orientated as seen in the picture) - secures...

Designed up this dealer button to use in home games or have just as something laying around for any poker fan. It was inspired by a dealer button in Pokerstars VR. Printing: Ring - Infil to add weight, supports needed for spade inset. Letter...