zero two headband 3d models

Take what's theirs and make it your own! ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1...

Take what's theirs and make it your own! ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1...

The "Anker-A" part has 2mm holes at the ends into which the other two parts are inserted. The "Anker-B" part is held by an M3 set screw and can be replaced if a writing stylus with a different profile is used. The "Anker-C" part is glued to the...

 It is working nicely through the gear train but the escapement gear is just a little tight against the gear_train gear so I modified the front and rear rails to push the escapement gear toward the balance section by about ⅔ of a mm to help keep the...

The 3D printing Sparrow figurine has his long hair dreadlocked and customarily wears his goatee in two braids. The author of the model made sure to include Jack’s signature tricorne hat, bandanna, and lots of intricate beads and ancient coins that...

Take what's theirs and make it your own! ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1...

After all, the "PSU attachment" is fixed to the same frame as the other two screws, so I don't think it is necessary to use it, but I put it on just in case. If you are concerned about it, please remix the screws so that they are attached to a...

The end stands are connected using two pieces of aluminum deck rail which I already had, but other materials can also be used for this such as rectangular wood pieces or dowels or by screwing the pieces to a flat base. I did not provide holes for...

The model features the craft’s trademark three wings: a stationary dorsal stabiliser and two articulated flanking side wings. The 3D printing Lambda-class shuttle is heavily armed with a pair of forward-facing double blaster cannons, two wing-mounted...

For those customers who have already purchased the Treebeard figurine or are planning to do so, every version of the Merry Brandybuck model comes in two variants to choose from - an independent static figurine (marked “Stand” in the “Source files”...

Basically, I've split the Selector carrier in two parts, which makes it easier to replace the endstop sensor on top or add some features like the servo variant or some laser detector, without the necessity of reprinting the whole carrier. You'd...

The 3D printing model's chosen scale is 1:34 for the FFF/FDM version and 1:68 for the DLP/SLA/SLS version.VERSIONS' SPECIFICATIONSFFF/FDM 2.0 version features:- Contains 30 parts;- A printed ship is 271 mm tall, 170 mm wide, 368 mm deep;- The updated...

The 3D printing scene depicts two creatures clashed in a heated battle of seemingly equal powers and abilities. You may choose to display the powerful Venom independently or together with his ruthless opponent. The only question is, will you dare let...

* Install the probe mount to the extruder plate using two short M3 screws. * Remove the 4020 duct, BMG and hotend, if installed. * Sandwich the extruder plate between the extruder stepper and the BMG, and start the three long M3 screws. Do not...

The scene most likely takes place somewhere in the middle of the crime-ridden Gotham City so it is no surprise that the figurine is wielding two bulky guns, pointed at different directions. The 3D artist made sure to include all the trademark...

The 3D printing model’s chosen scale is 1:350 for the FFF/FDM version and 1:700 for the DLP/SLA/SLS version.VERSIONS' SPECIFICATIONSFFF/FDM 1.0 version features:- Contains 50 parts;- A printed model is 152 mm tall, 416 mm wide, 312 mm deep;- There is...

Have much fun with it =)30.03.2023: Added two 4K videos to the description that show the complete setup process of the Arduino installation, code upload to the ESP32 board and the WiFi setup on Microsoft Windows 11 and Apple macOS. Hope this will...

Note there are two similar parts that could be the Lid knob bottom, you need the one with an hexagonal seat on the inside.Place the magnet and the spacer into the top of the Lid knob.Press a M5 nut into the Lid knob-bottom, temporarily using the M5...

The two elaborately detailed donor cars stacked on top of each other rest on immense tractor tyres that elevate them above the ground and represent the militant Colonel's authority. So don't miss out on the opportunity to 3D print an addition to your...

Both versions are to be identically assembled to the body of the bike;- The assembly of the front and rear shock-absorbers requires 2 regular ball pen springs and additional "pins" made out of short pieces of regular 1.75mm filament;- Rotation of the...

Take what's theirs and make it your own! ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1...

In order to ensure the cleanest 3D printed result, Otachi’s tongue was extracted from the beast’s mouth, while the two parts of Kaiju's signature crest were cut off as well.All assembly parts are provided in STL files of FFF/FDM version in...

For those customers who have already purchased the Treebeard figurine or are planning to do so, every version of the Pippin Took model comes in two variants to choose from - an independent static figurine (marked “Stand” in the “Source files” tab)...

HOW IT WORKS: If temperature rises +1°C above set limit (for example, set limit is +40°C and temperature rises to +41°C), two “MH1210A” controllers start fans (ventilation) and drop temperature to +40°C. Tested temperature limit inside enclosure...

The 3D printing model's chosen scale is 1:400 for the FFF/FDM version and 1:800 for the DLP/SLA/SLS version.VERSIONS' SPECIFICATIONSFFF/FDM 1.0 version features:- Contains 42 parts;- A printed ship is 133 mm tall, 480 mm wide, 469 mm deep;- Assembly...

This first version is specific to the Prusa i3 MK3S+, however the Drill Bit Version of the MK3S+ SPA will work on both the MK3S+ and the MK3S (and may also work on the MK3, but I have not done any testing at this time); details on the Drill Bit...

Two sharp attachments on the nose of the spacecraft and two vertical stabilizers in the back were installed to further aid the flight control. The top hull plated with ablative armour is riddled with authentic patterns, joined by the name of the ship...

ABOUT THIS 3D MODEL“Batman has two primary modes of transportation: swinging from Gothic clock towers on his Batline, and cruising around Gotham in the Batmobile.”The sleek, long and low Batmobile featured in the 1989 Tim Burton’s Batman movie struck...

If you have a switch that toggles two connections at once (4 terminals), the ground wire can be toggled as well, but I think it might be better to keep the ground connected at all times.Make sure the toggle switch is rated for at least 5 amps (it...

There were also prepared two different types of bearings for front and rear wheels of the 3D printing car. The reason why the front bearings are thinner is to allow for the simultaneous movement of front wheels with the help of a steering rack that...