zero tolerance zt 0400 3d models

Customized version of https://www.thingiverse.com/thing:2318105 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2318105

Human: Modified Design of a Customized Solar System Model\nCreated with Customizer!\n\nCustomization Details:\nOptions Selected:\nPlanetary Count: Five\ntwist Value: One Degree\nTolerance Level: Two and a Half Percent\nWorm Gear Width: Six Point...

Customized version of https://www.thingiverse.com/thing:468917 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=468917

A crucial component for assessing the precision of three-dimensional printing technology is being developed.

Customized version of http://www.thingiverse.com/thing:53451 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=53451 Instructions Using the following options: nTwist =...

The Anet A8 printer is optimized for high-quality prints with its default settings. The layer height of 0.2 millimeters allows for crisp details and smooth transitions between layers. Thin walls, measuring just 0.4 millimeters in thickness, are ideal...

Just another quick check of our limits, but much smaller and faster to run through the printer. ...It runs from 0.05 up to 0.30 in increments of 0.05.

Customized version of https://www.thingiverse.com/thing:53451 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=53451

Push out as many pegs as possible after printing. The numbers on each side indicate the gap width between the triangular case and each peg in millimeters. On my own print, I was able to remove pegs with gaps of 0.20mm and wider but those with 0.15mm...

After struggling with elephant foot consistently appearing on my prints, I discovered there were few tests to help eliminate it efficiently. Most methods I found took an excessively long time - I needed something that could produce a print in under...

Increased diameter of the balljoints from 12.6 to 13mm for a tighter fit. ...If yours feels loose and has a big physical deadzone, try these out they should be slightly tighter.

Customized version of https://www.thingiverse.com/thing:3867358 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3867358

Ran through Netfabb software to resolve complex geometry issues and ensure a flawless 3D model.

Hole - XY and Z column -XY 1 unit = 0.1mm

I couldn't fit the Phone Clamp over the arm, so i made a new one with a bigger hole so that it easily slides onto the arm. ... I tried sanding the original (gave up) and also tried scaling the part to %115 which also didn't work so i made one that...

65 mm x 65 mm Prefer if printed 50% larger will have clean lines Background thickness is 2 mm Text thickness is 0.5 mm Text layer starts at Z height of 2.10 mm

I boost the threshold of the initial switch to prevent jamming since the switch had been obstructing its function.

this is a clearence test it will tell you how much room you have to print modles the clearence is added to one side and not the other so the total gap is the number stated all units are in mm

Eng: Must set in cura setting HORIZONTAL EXPANTION minimum to -0.1 since the design both pieces are the same dimensions. then go adding more space until the print fits. Esp: Para que esta pieca encaje perfectamente se recomienda configurar en cura...

Don't you hate it when a ‘test print’ takes hours and use up like 10% of your filament spool? This should be faster.The gaps between inner and outer rings are 0.1mm/0.15mm/0.2mm/0.25mm/0.3mm each(measured perpendicular to face) 1.671mm is the width...