zenni oculus quest 2 3d models

<p>Remixed from <a href="https://www.thingiverse.com/thing:4629958">https://www.thingiverse.com/thing:4629958</a></p> <p>This clips on to the loop on the back of the elastic headstrap.</p> Category: Video Games

I wanted to use the head strap of Quest3 with Quest2, so I made it.Please be sure to read the notes below and use at your own risk.When attaching and detaching parts, there is a possibility of damaging the VR device itself.Depending on the strength...

<p>This is a great design, but it had really flimsy attachment points for Koss headphone elements. I broke at least five in the process of building a set for myself and a friend, printed in PLA+ and PETG, tried different print settings but there just...

This is basically just the model by tigerflip, but with a hole cut into the bottom. I measured the straps on my controller to ensure they could pass through (including the plastic thingy) but the fit is snug. You should pinch the strap and push it...

Very light fan cooling system for Vr headset. It makes those beat saber sessions a lot more enjoyable. Also the foam does not get all damp after a long session. It's the perfect addition to the headset! Uses a small 5v fan (30x30mm) and a 1s...

<p>I printed it standing up with supports for the bridge</p>

Just removed 1mm from the center of the STL I personally printed in PETG because I like the durability and flex.

Created this to go with a headset mount so the controllers fit inside the elite headstrap

Dies ist ein Remix von "Mike vom Mars" https://www.thingiverse.com/thing:4025967 zu dem Brillenträger und Ständer gibt es noch eine zusätzlichen Träger zum aufsetzen, der das Elite Batterie-Pack trägt. Es wurden die Controllerbefestigung etwas...

I wanted to use the head strap of Quest2 with Quest3, so I made it.2023/10/21 The shape has been adjusted to fit better. Cable ties are no longer required.Thickened the thin parts to increase strength.I put the left and right in one file.2023/10/19...

The Quest2 is front-heavy and slips down as you wear it, so I made a battery mount that doubles as a counterweight that attaches to the back of the headband. The battery mount should be installed by sliding it vertically after installing Quest2.

<p>The headset mount is a remix of a design from lensfort on Thingiverse that allows me to hang it on my pegboard: <a href="https://www.thingiverse.com/thing:4630669">https://www.thingiverse.com/thing:4630669</a></p><p>The controller mounts are an...

See https://www.thingiverse.com/thing:4630669 for details. Modified to allow mounting to the CAMVATE Universal C-Clamp: https://www.amazon.com/gp/product/B018RLY6B2/ Particularly useful for temporary desk mounting, such as when doing VR dev...

This adapter is slide-in assembly. The main purpose of using the sliding-in installation design is to reduce possible damage to the main body of the VIVE DAS during installation. please refer to the animation for details.

Modified Przemoc's design to wide fit I am not a professional modeler, so this modeling is a bit sharp I use this and the fov is about 10 degrees wider

My clip broke when I threw the disk too hard in Echo VR, I designed this so it can connect without a new strap. It is a bit hard to put on and it is snug at the beginning, after some time it will lossen up and be even better than the original. ... ...

This is not my design. ...Only cut the back of Bobo-VR part to be printable with a smaller printer

This is a remix of another users model that wasn't wide enough. ...I went ahead and rescaled the model and added a spot to insert the grips of the controllers., the grips do fit rather snug and the wrist cords need to be over the top when inserting.

Come si vede dai file, si tratta di un remix degli oggetti sopracitati ( https://www.thingiverse.com/thing:4629343 e https://www.thingiverse.com/thing:4629958), uniti e opportunamente migliorati per evitare una stampa di 4 ore per pezzo, ma con la...

Designed this Cable clip to use with any cable up to 7mm thick. ...any cable smaller will fit but be a bit loose Printing: orientation: Make sure the print is on it's side this way it prints best and cleanest infill: best result use 100% but...

<p>Dies ist ein Remix von "Mike vom Mars" <a href="https://www.thingiverse.com/thing:4025967">https://www.thingiverse.com/thing:4025967</a></p><p>zu dem Brillenträger und Ständer gibt es noch eine zusätzlichen Träger zum aufsetzen, der das Elite...

Fits the right hand controller to support it to your shoulder for more precise aiming. Tips are appreciated! ... thank you so much.

Improves better immersion in VR by being able to release the controller from the hand. Must be printed on TPU. ...Adhesive Velcro is required.

Remixed from https://www.thingiverse.com/thing:4629958 This clips on to the loop on the back of the elastic headstrap.

works with https://www.thingiverse.com/thing:3666505

This cover is a remix! I used the snap-fit file, and I see a lot of decals out there, but nothing with designs for a 3D printed cover. I only found one other design, a Venom design, which looks incredible. ... You can find the others here: Original...

MODEL_DESCRIPTION

This is a simple way to manage your headset cable so it doesn't hang down and get caught on anything while playing with your VR headset. I am working on an alternative design so that you don't have to remove the velcro straps everytime you wrap up...

Remixed handler for bobo-vr strap back part. Many thanks to author of original stand, it's very good designed. ...

Just removed 1.5 mm from the centre of the STL I printed in PLA but will print another in PETG for the durability and flex.