zenni oculus quest 2 3d models

This is a gun stock i created for the Quest 2. It helps with immersion and also helps with aim a little. I have tried to make the design as simple and user friendly as possible but please note that some sanding will be required (2-3mins per part) as...

Snaps firmly onto the rigid arm of the Elite Strap and holds the Oculus Link cable. ...The Link cable can be removed without removing the clip.</p> <h3>Print instructions</h3><p>Print on one side; brim recommended for improved bed adhesion.</p>

Simple little print I designed to replace the original Quest 2 controller cord cinch which my son broke. Works great! It pressure fit nicely enough for me, but I still glued the outer edges, just in case. I printed it at a 0.15mm resolution...

I decided to try to make locks that would attach to the stock Oculus wrist strap using flexible material. I went through several iterations before I hit on this design that has enough friction to hold onto the string tightly, orient the strap in...

Stock, the Oculus Quest2 does not fit me very well. If I pull the band low enough to keep it from slipping off, there is a huge gap at the bottom of the headset. This print allows me to have a very good fit with no gaps and keeps the headset well...

Cable clip for your Oculus Link cable, just snaps onto the side of your headset. This helps relieve stress of the very strained and weak USB C connector on your headset. Best printed in ABS or PETG but can be printed in PLA and will probably work...

5 walls, 0.1mm, x2 infill lines, triangles, 20% infill Cut Oculus Strap as close to the old clip as possible. Melt the cut end until there is one solid line of plastic on the end on the strap, for strength reasons. Print the new clips and use the...

The internal grooved one should accommodate a official Oculus Link cable. The top edge cable holder is a little larger in case you want to hold a headphone cable also. You may need to file down the opening a bit, if it is too small for your...

Print replacement straps for your Oculus elite (with or without battery) strap.&nbsp;There are three versions included:One piece original size (needs bigger print bed)One piece Prusa MK3 bed size (should fit most heads but may be tight if glasses...

Link to battery holder V2 with a more secure design and less "moment" weight so it feels lighter than V1: https://www.thingiverse.com/thing:5250979 this is a remix and my first design so that you can have a power bank plugged into the oculus while...

Link to battery holder V2 with a more secure design and less "moment" weight so it feels lighter than V1: https://www.thingiverse.com/thing:5250979this is a remix and my first design so that you can have a power bank plugged into the oculus while...

.2 &nbsp;2 layers concentric infill

Slight remix to hang both controllers with only 2 screws.

After I finished sanding and spray painting this, I connected the triggers and buttons, and used a normal printer to make a BMW logo sticker to put instead of the Oculus logo. You will also have to use a knife to widen the whole at the bottom a...

remix grip from https://www.thingiverse.com/thing:4651978 608 2RS bearing * 2 20mm magnet rubber band M3 bolt nuts

This model requires a 1.5m hook-and-loop fastener. ... You should cut the hook-and-loop fastener to 5pices. 3 for the battery - mount, 2 for the mount - strap. ... The battery must be mounted upwards.

Its a remix only bc I added 2 screw holes to the headset part, other than that credit goes to the OP. Thanks Headset didnt need support but the controllers did. I used tree, everywhere. ...

... is a Minimal Print. ...intended to save filament Designed for both Headset and Controllers Required materials: 8 screws Notes: -You will need to print of 4 of these, 2 for the headset 1 for each controller -Print on its side to ensure maximum strength

... the layard. To install the layard: first put the lanyard in the hole, then loop over the clip and secure it in the 2 little hooks on each side. See photo. That how I install it but may be you will an other way haha. ... Print it flat, it's easier

UDATE 2: Re-Meshed the wings “conector” in blender, the V2 was made measuring the physical model, while this V3 is made by using the virtual model, allowing for a perfect fit with the base, they both work equally well, but it might be easier to align...

... Then loop over the clip and secure it in the 2 little hooks on each side. See photos. ...That how I install it but may be you will find an other way haha.Print it flat, it's easierPrint SettingsRafts:NoSupports: NoInfill: 100Filament: PLA Grey

There are 2 versions of this, one with AND one without secure tabs. Designed in Fusion and printed with Windows Print 3d using ABS. The rims for both are beveled. 1. Without Tabs - Just press the O into the rim. The rim is beveled and is...

There is a recess within butt to conceal the knot. There is a hole in the butt that will fit a quick release sling swivel. Support free printable parts Print left or right handed controller clamps Print 3 clamp nuts Print one of each of the remaining...

It appears that this is a large block of text that seems to be a tutorial or guide for creating and using a 3D printed rifle accessory, specifically designed for use with the Oculus Quest VR headset. However, I'll do my best to break it down and...

I was wondering if Quest 2 straps could be made compatible to the Quest 1. Indeed, it is possible. I liked the design of @sekazi, but the adapter is movable, so I decided to make it 2mm longer and added a small clip at the end, so it does not get off...

Protective/decorative covers for your Oculus Quest 2 controllers! The holes allow proper tracking of the IR LEDs. Designed to be printed in TPU and slipped directly onto the controller. Three versions: (1) Original - Minimal with small holes. I...

I was wondering if Quest 2 straps could be made compatible to the Quest 1. Indeed, it is possible. I liked the design of @sekazi (https://www.thingiverse.com/thing:4624192), but the adapter is movable, so I decided to make it 2mm longer and added a...

Just my design of a Anker Powercore 2 10 000mah holder for Oculus Quest 2 (for elite and basic strap) The locking of the battery is done with a cable tie

https://youtu.be/3c4S7vyELSE for oculus quest 2

This is a quick IPD checker I made for the Oculus Quest 2. Very handy for when you want people to try out VR without needing a ruler to check their IPD The way to use it is by lining up the left point with one eye, and seeing which point their other...