zenitco ak charging handle 3d models

I haven't printed this yet, but i know it will work since I have used the same measurements for another charging handle. I will soon post a picture of my print and the settings I used. ... (The holes are made to fit a small bolt, only for the...

These are M-LOK Zenitco style grips based off the RK-1, RK-2, RK-4, and RK-6 from Zenitco. An M-LOK mount based off the B-25U 45 degree mount is also included. The RK-1, RK-2, and RK-4 have an internal storage diameter of about 27mm, with varying...

This one for Ak Jinming j12 Video how to remove stock lower handgaurd of Ak j12 jinming aks74uhttps://www.youtube.com/watch?v=J-vIdef_GM8

The stock charging handle is designed to work ONLY with the OEM Glock Serration size and pattern, and I wanted to use my Aim Surplus G17 slide with an RMR cut-out. This CH will engage the serration pattern of the slide as well as the optic...

The stock charging handle is designed to work ONLY with the OEM Glock Serration size and pattern, and I wanted to use my Aim Surplus G17 slide with an RMR cut-out. This CH will engage the serration pattern of the slide as well as the optic cut-out...

not the FGC6(S) this is a pure lie cosmetic piece on the FGC68 so no hay spring pressure is need to make this Charging Handle Assembly work. just enough to push the assembly back forward. after slapping the thing! haha spring size: OD 7mm, wire...

not the FGC6(S) this is a pure lie cosmetic piece on the FGC68 so no hay spring pressure is need to make this Charging Handle Assembly work. just enough to push the assembly back forward. after slapping the thing! haha How do I assemble the...

The power wire for the charging base can routed from the back, bottom or right side to prevent it from getting in the way as much as possible.Prusament PLA gives the best results.*BONUS: Download the .usdz file to see it in Augmented Reality (AR) as...

My solution involved creating this small charging handle that mounts in the hole left by the removed rear sight. To install it, simply print the model, remove the rear sight, and secure the charging handle in its place using epoxy. Although this...

this charging handle was suppose to look like the raptor charging handle, but for the airsoft KSC MP9/TP9. I don't know if it's the same for the actual gun. actual important part: There are 2 version of this model. one is a whole part that you can...

Be advise, this model was tested on E&L aks74u essential AEG replica and with LCT RP-1 enlarged charging handle and may not fit on other E&L series or other RP-1 manufacturers, if you tried it on other replicas or manufacturers and find that it fits...

This retainer prevents the charging handle and spring from falling off. Simply snap it onto the last rail in place. The filament requires only +/- 600 mm to secure firmly without fear of breaking it while trying to remove it from the front rail. ...This...

there are 2 versions of this Charging Handle Assembly. one were you still would need some glue to place the charging handle piece on. with this version a regular FGC9 Charging Handle design can be used. and a M3 Bolt version the parts of this are...

Side charging does not seem to create substantial sideways torque, so this is unlikely to break the blaster like the Modulus Tri-Strike does a lot. Handle is surprisingly durable so far. It MAY work on the Maverick or other slide blasters, but I...

Since no one offers a side charging handle for novak style sight cuts I designed a couple jigs that would allow you to file a piece of 1/2" or 3/4" round stock to fit the novak sight cuts to use as a side charging handle. Jigs 1, 2, and 3 are for...

Shooting with a CMMG Rimfire Conversion Kit for your AR15 allows for gas to travel back along your stock charging handle. This insert helps reduce the amount of gas that reaches your face. See https://www.youtube.com/watch?v=-SYMDHDBNAw&t=3m30s...

The FM-9B forward charging handle is pretty close to the rail and I can't see to source the paratrooper very at this point in time. Fortunately, /u/captian_carrot actually made a 3D model of on in onshape as opposed to just the raw STL. this gave me...

The charging handle needs a 47mm M3 with nut, which goes behind the factory rear sight to lock it in place, preventing it from moving forward. I designed this for my K-26 spring upgrade since it made priming much more challenging. This modification...

AR-15 and M16 milspec charging handle, modified to use a standard pen spring and a paperclip at the pin. This works in an AR-15 and actually stood up to being racked a couple dozen times, when printed in PLA+. It could probably be actually usable in...

This part is designed to provide a left side charging handle for the Ruger 10/22 very popular rifle. It allows right handed people to perform tactical reloads with their right hand never leaving the pisto grip with the finger on the trigger in...

This part is designed to provide a left side charging handle for the Ruger 10/22 very popular rifle. It allows right handed people to perform tactical reloads with their right hand never leaving the pisto grip with the finger on the trigger in...

This part is designed to provide a left side charging handle for the Ruger 10/22 very popular rifle. It allows right handed people to perform tactical reloads with their right hand never leaving the pisto grip with the finger on the trigger in...

AK model rifle equipped with a compact barrel and advanced upgrades inspired by Zenitco's designs.

Designed from scratch but based on the original STL from Adrien (https://www.etsy.com/listing/957928696/the-gecko-3d-printed-foam-dart-blasting) - "bottom priming" for higher cadence - picatinny rail for your own grips or attachments - fit original...

Model based on Zenitco catalogue from 2016 and Karden photos. Mostly in use today is the PKM mount "Putnik", but this was the mount dedicated for 5.45 and 7.62 AKs. Printed as a prototype before making an CNC one. !! The weakest part of the project...

I made this because i got the airsoft gun and wanted to mod it but did not want to buy overpriced mods so i made them myself and it works.I used some existing models and modded them to fit multiple mods at once.

this is purely a cosmetic chance. but it does make the middel part thinner. and is 2.60 mm longer. ...the assembly of this part is the same as the original.

I get great results by applying some elbow grease and taking my time. After 10 to 15 minutes of careful sanding, everything falls into place and works like a charm. ...If the part is stuck too tightly, I make sure to use a file and add some lubricant to...

Fits as OEM.

Делал для своего проекта рукоять затвора на цыма 040 калаш, решил закинуть сюда еще несколько вариантов, вдруг кому надо, они частенько ломаются. Варианты: - АК - обычная рукоять - Валмет - рукоять с шариком поднятая вверх на 20 градусов, видел...