zd 9116 3d models
252 3d models found related to zd 9116.thingiverse
Rear bumper for the zd 9116 Pirates 2 trucks. You will need 5 m3 x 25 screws. ...Use a heat gun or blow drier to soften the big hole side pieces and slide the pipe in, the plastic will cool and hold the pipe piece in place
thingiverse
Front bumper for the zd 9116 Pirates 2 trucks. You will need 5 m3 x 25 screws. ...Use a heat gun or blow drier to soften the big hole in side pieces and slide the pipe in, the plastic will cool and hold the pipe piece in place
thingiverse
When bashing a ZD Racing 9116 V3 it appeared that the Aluminium Bottom Plate easily get bent after heavy drops. This Backbone is mounted between the two Shock-Towers and will increase overall impact resistance a big deal. you Need 3 x 10mm M4 Screws...
thingiverse
Beefed up chassis brace for the ZD Racing 9116 Pirates 2 Monster truck - may fit the truggy and other variant. This addresses a weak point on the design and makes it much harder to bend the chassis. ... Requires some M3 screws and nuts to mount
thingiverse
ZD Racing 9116 1/8 Inner Guard This is an inner chassis guard that replace the original guards mounted on the sides of the base plate. The last drives on gravel the car collects "rocks" that stuck my gears and other things, thats now history. ... My...
thingiverse
This is a modified 3d model of the ZD Racing 9116 Pirates2 lower suspension arm (part 8042). I beefed up the end of the arm. Survived a cartwheel that broke a front shock and front suspension mount (next model, it seems). Haven't tested with...
thingiverse
This is a modified 3d model of the ZD Racing 9116 Pirates2 rear lower suspension arm (part 8042). I beefed up the end of the arm and cut a hole in the wide part. Roll bar mounts aren't sized correctly, they don't hurt, but fitting the roll bar might...
thingiverse
This is a modified 3d model of the ZD Racing 9116 Pirates2 steering cup (part 8135). I beefed up the hub and the steering arm (both places that broke on the original and on previous versions). Thus far they have survived a cartwheel (which the...
thingiverse
ZD Racing 9116 1/8 Front Bumper Searched for an strong and easy to print Bumper for my ZD Racing Truggy. Some can be found, but none suite my needs. So i build one from scratch on my own... This is a work in progress, its functional but the Design...
thingiverse
ZD Racing 9116 1/8 Chassis Pins (Holder) My car slipps upside down few meters after a fail jump - without chassis put on it, so my chassis pins rubbed off.
thingiverse
https://bit.ly/3r94qFN Just a mod of the ZD Racing 9116 Pirates V3 Backbone https://www.thingiverse.com/thing:4551083 to allow it to be printed in 2 parts (which will fit on most 3d printers). Bolted together with 2x M4x20 bolts and nuts. ... I...
thingiverse
ZD Racing Pirates 1/8 RC vehicles (MT, Truggy and Buggy ) Servo Saver arm, beefed up for 3D printing
thingiverse
I crafted this body from scratch, rebuilding it after my ZD Racing 08427 monster truck suffered a costly crash during its maiden run. The body itself is a sturdy 2mm thick and comprises three interlocking pieces that are held together by precision...
thingiverse
ANOTHER EDIT: I have made some changes. The FF part is now reinforced further as I am so done with them failing at the chassis screw points. I have also made versions with predone M4x0.7 threads that make tapping out the holes sooo much easier ...
prusaprinters
<p>more beefed up than original, it is braced against tower mounts</p> Category: R/C Vehicles
thingiverse
replacement of the original, more beefed up version
thingiverse
more beefed up than original, it is braced against tower mounts
prusaprinters
<p>replacement of the original, more beefed up version</p> Category: R/C Vehicles
prusaprinters
<p>replacement of the original part, more beefed up</p> Category: R/C Vehicles
thingiverse
Hallo, ich hab während einer schlaflosen Nacht meinen Pirates 2 Offroader repariert, dazu habe ich dieses Teil (Car Steering Cup) entworfen. Ich weiß nicht genau ob das gut hält, bis meine Ersatzteile da sind werde ich dies testen. Gedruckt sollte...
thingiverse
I managed to wreck one of these on my brand new truck and since I couldn't find any sources for replacement parts, I decided to take matters into my own hands and make one myself. With my 3D printer, the first version turned out a bit too precise...
thingiverse
- Barre de renfort châssis Eléments nécessaires : Tube (inox) diamètre 16 mm longueur 245 mm Prendre la cote sur le véhicule une fois les deux renforts installés pour confirmer la longueur de la barre. Fixation du renfort avant : 2 Vis M4...
prusaprinters
<p>I Tried 3perimeters and 15 infill, will see how it holds</p> Category: R/C Vehicles
thingiverse
I Tried 3perimeters and 15 infill, will see how it holds
thingiverse
ZD Racing lower front A-arms for 9116 Pirates 2 Monster Truck part number 8042 Reasonably faithful replication of the original molded items, could be further optimized for 3D printing. Does not include the sway bar mountings as I do not run them....
thingiverse
Hallo, ich habe hier eine Stoßstange für den ZD Racing Pirates2 entworfen, sie besteht aus 4 Teilen die sich mittels Kabelbinder sichern lassen. Die "Federstärke" kann man sich heraussuchen, was da Sinn macht weiß ich auch nicht genau, ich habe...
thingiverse
Hallo, ich habe hier eine Stoßstange für den ZD Racing Pirates2 entworfen, sie besteht aus 4 Teilen die sich mittels Kabelbinder sichern lassen. Die "Federstärke" kann man sich heraussuchen, was da Sinn macht weiß ich auch nicht genau, ich habe...
thingiverse
This is a battery tray to accommodate a large 5000mAh 3S battery. It uses the same screw locations as the original tray but is larger and positioned to allow for increased battery size. Max battery size on render graphic. ...I use it with CNHL G+...