z3 compact orange 3d models

 This is a more compact case for day hiking, etc.  When assembling, put the lens in the base, screw the middle part with the hexagonal grid on, and then put desiccant in the top and screw it on.  I made the middle and the top the same...

https://www.larsonelectronics.com/product/47383/portable-magnetic-mount-led-light-emitter-6-10-watt-leds-675-l-x-90-w-spot-beam-9-48vdcBuy American CompliantThe Larson Electronics LED10W-6R-HT LED Light offers high light output in a light weight,...

I could make the base taller, but would make it less compact. You need a wrench to tighten the bolt, but that is a minor anoyance. I am going to work on getting more mountain streams using this new mount. Here is a link to some audio recordings I did...

It's mostly the same as LMNCs schematic, but a bit more compact and tailored to the parts I had. Yours might be different depending on the parts you can source. I've socketed the transistors and capacitors on the oscillators so that it's easier to...

The only thing specifically required by this print is some compact plumbing part that can connect on to the 1/2" BSP thread of the float valve. The printed spanner is designed to fit a 1/2" BSP to 1/4" push-fit adapter with a hexagonal body measuring...

This head is more compact and is capable of looking straight down however it is not suitable for use on the jib since the balance of the jib is disturbed as the camera moves out. All parts of the system are WIFI linked and work together or...

Something that is compact, lightweight, simple to use, and that can be handed to just about anybody, pre-loaded and ready to go, to turn them into a anti-tank threat. Obviously, if you're going to be making 3 or 4 of them to hand out to your...

Increased the hole size to 2.75mm for easier fitment.New ADXL-345 MountAdded a file that goes onto the Front of the extruder for an ADXL-345You will need to switch out the M3x6mm Screws on the Top Front of the Left and Right wings to M3x8mm Screws...

UPDATE REV4: After reverting to this form factor from the v-shape due to issues with low-mounted v-shapes on compact X-quad builds getting antenna pads too close to props, I uploaded a revised version that is sturdier, requires no clipping of parts,...

Some of the hinge sections are quite thin as I focused on compactness, but are suitably strong on my models, using good quality PLA. A good first layer is critical on the 'lower door' parts.</p><h3>Parts Printing</h3><p>For one box you will need to...

This mount is very rigid, there is no droop or wobble induced by having the bulk weight far away from the gantry, it's also as compact as I could get it with the goals I had in mind. The hotend is placed exactly where the original hotend would be, so...

Last year, as part of Oceanography for Everyone, we unveiled the BeagleBox, a compact, affordable, rugged field computer powered by a BeagleBone Black. The initial BeagleBox didn't promise much, it was designed for basic field work and, most...

Using a "Sabrent USB 3.0 to SATA" adaptor, chose that as it is small and compact. Other adaptors needed to much depth.</p> <p>I have finished printing all of the parts and it is holding together well! Updated with some glamour photos of the final...

Its size is compact, making it ideal for taking it anywhere curiosity can reach you. The form of the gadget was born from the concept of "destruction", because we need to destroy, or in this case disarm the objects, in order to know what is inside...

This versatile system enables adaptable racks, loops, and compact shelves for the "[Elfa Utility Board](https://www.containerstore.com/s/elfa/components/elfa-utility/platinum-elfa-utility-board-wall-mounts/123d?productId=10034901)" pegboard system. A...

Together with this 3d printed housing it results in a compact receiver. The parts needed for this receiver are: • 3d printed case • PS1 / 2 controller connector • ESP32 d1 mini • BlueRetro_PS1_Shield (with components) • 4 pieces m2x16...

A set of 3D printable parts to compactly combine two LRS-350 PSUs into a single unit with optional voltage and current displays. I created this device to consolidate ten individual power bricks for each compute node in my home lab into just one...

Extra options can be mounted on the back (holes exist for screws for the X-axis belt and any x-axis belt holder you can find around here) 2 - Bowden Mount - A mounting bracket designed specifically for Bowden-style printers, featuring a robust design...

It is small, compact 60g extruder with 3:1 gearing. I bought mine from PrintedSolid.com (<a href="https://printedsolid.com/products/e3d-titan-extruder">https://printedsolid.com/products/e3d-titan-extruder</a>).</p> <p>I have been working on a bracket...

It’s designed to be portable, compact device and it’s open source. In previous build we used several boards to make a similar project. For this one we can use Adafruit’s Feather and the Prop Maker Feather Wing.</p> <p>Check out the learn guide for...

* The code of many towers is very compact. That's good. But it's also often uncommented and difficult to follow, with lots of magic numbers being used without explanation. I often wanted to make modifications but couldn't figure out what could be...

Overall, such a concept ended up looking similar to its smaller version, but when you go compact and simple you will probably end up with a very similar build too :P&nbsp;Parts neededToolsHere is a list of all the tools you will need for building...

so stay tuned for the V2 Version with single 4020 Blowerfan and even way more compact design! here you can get my single4020 fan design now: https://www.thingiverse.com/thing:4757657 i still leave this online, as somebody would like too use the...

Terrain Overlay Tiles For Gloomhaven or MagHex Walls for GloomhavenMagnets are quicker to set up and clean up; or use plastic connectors its cheaperUpgrading to magnets can be done whenever and if everWhen and if using magnets four minimum is...

BeamCase is a system theat allows you to create your own case with the combination of 3d prints and Makerbeam XL profiles (or similar 15x15 aluminium extrusions).Beamcase SFF is a system optimized towards compact builds with good cooling while still...

These are all the mechanical parts to build a superlight version of a popular design for a compact tri-band endfed antenna for 40, 20, and 10 meters with a loading coil. The antenna is basically the same design as described by VK3YY at...

The design is compact and could be made quite a bit smaller with a smaller battery and using a standard square box body. This is something I will do at a later date. Previous model description: I hooked up a 1400mah battery and drove this home from...

This is a simple and compact case for the Odroid H2 and hopefully updated to be compatible with the H3 (untested since I don't have one).The case is in two parts and there are two variants of each half. The bottom can support two 2.5" HDDs or come in...

... preferences. This unit comes with a power cord for completing electrical connections.Applications: Pedestrian safety, type E forklift operations, zone lights, warehouses, compact vessels, carts, illuminative safety, industrial buildings and more.

If we flip the frame and add new mount options, I can fly any flight controller and have a compact center of gravity. I can also fly different lipo positions which is a cool way of customizing. Advantages of my Mod: - Fly any flight...